GRASS VALLEY K2 BASECAMP EXPRESS Installation And Service Manual Download Page 146 | Manualshive

Page: 146 / 366

background image

Click

Next

.

You do not need to enter or configure anything on this page.

The FTP Server Configuration page opens.

Configure FTP Server Configuration page - Basic K2 SAN

This page appears only if the server has the role of FTP server.

Do not modify these settings. Leave at default values of Max FTP streams = 4 and FTP Data Socket
Timeout = 60. Only qualified Grass Valley personnel should specify other values, as these settings
are intended for use only with custom systems designed by Grass Valley.

1. Click

Next

.

The Completing the Configuration Wizard page opens.

2. Click

Finish

.

The wizard closes. The server restarts.

Wait until all startup processes have completed before continuing.

Proceed as follows:

•

If you have NH servers, configure them next.

•

If you do not have NH servers, configure K2 clients and/or other iSCSI clients on the K2 SAN
next.

146

K2 SAN Installation and Service Manual

02 February 2012

Configuring and licensing the K2 SAN

«
...
144
145
146
147
148
...
»

Summary of Contents for K2 BASECAMP EXPRESS















































































































































































































































































































































































Reviews:

No comments

Related manuals for K2 BASECAMP EXPRESS

Brand: Cambridge Audio Pages: 4

Brand: Cambridge Audio Pages: 2

VLT DeviceNet MCA 104

Brand: Danfoss Pages: 18

Brand: Danfoss Pages: 138

Brand: Danfoss Pages: 108

Brand: Danfoss Pages: 149

Brand: Z3 Technology Pages: 86

Infinity IEC-2001

Brand: LevelOne Pages: 2

GD200-037G/045P-4

Brand: INVT Pages: 266

Brand: Xantrex Pages: 58

Brand: M-Audio Pages: 48

Brand: B&B Electronics Pages: 15

Brand: National Communications Pages: 20

Brand: AXIOMTEK Pages: 2

basic-line DCC 1-00

Brand: axing Pages: 4

Brand: Linear Pages: 3

Brand: Lindy Pages: 14

IFS MC250-4T Series

Brand: Interlogix Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands