GRASS VALLEY IQUCP25 User Manual Download

Page: 316 / 338

316

Maintenance & Troubleshooting

Loading (Selecting) Software Version on the UCP

3901 / IQUCP25 / IQUCP50

4 Click

Yes

The Unit License dialog closes. When the unit has restarted the new licenses will be

active.

Loading (Selecting) Software Version on the UCP

3901 / IQUCP25 / IQUCP50

The UCP

3901 Card is a generic card and its functionality is set by the licensing that has

been enabled on it and by selecting a software version. A UCP

3901 Card may have more

than one license and software version (for example, Essence Processing and another

application).
The required functionality is selected by selecting the corresponding licensed software

version on the card.

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands