GRASS VALLEY IQUCP25 User Manual Download

Page: 299 / 338

299

UCP

3901

Multiviewer SDC

Chapter

User Manual

System - Setup

The

System-Setup

template (see Figure 9-8) comprises various information boxes which

display basic information about the Multiviewer SDC multiviewer (for example, system

status, product name and software version). It is also used to setup the following

Multiviewer SDC system details:

• System reset of the Multiviewer SDC multiviewer.
• RollCall settings.
• Multiviewer monitor output format.
• Multiviewer name.

Fig. 9-8: System Setup Template

Note:

The Multiviewer SDC multiviewer must be

System Reset

for any

saved setting changes on this template page to take effect. See

Carrying Out a System Reset

, on page 301.

This should only be done during off hours when the system is not in

use.

Booting takes about 75 seconds to complete during which

the card will be unavailable.

Parameter

Description

Product Name

Shows the name of the module. For example, ‘IQUCP25_206’.

Serial Number

Shows the Multiviewer SDC’s serial number.

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands