GRASS VALLEY 8920ADC - Instruction Manual Download Page 34 | Manualshive

Page: 34 / 40

background image

34

8920ADC Instruction Manual

Status Monitoring

SNMP Reporting

The Gecko 8900 Series system uses the Simple Network Monitoring Pro-
tocol (SNMP) internet standard for reporting status information to remote
monitoring stations. When SNMP Agent software is installed on the
8900NET module, enabled status reports are sent to an SNMP Manager
such as the Grass Valley’s NetCentral application.

There are both hardware and software report enable switches for each
report. Both must be enabled for the report to be sent. Software report
switches are set on the 8900NET Configuration web page for the Frame, the
8900NET module, and each module slot. Refer to the 8900NET Network
Interface Instruction Manual for installation instructions.

«
...
32
33
34
35
36
...
»

Summary of Contents for 8920ADC -









































Reviews:

No comments

Related manuals for 8920ADC -

MediaLounge DSM-520

Brand: D-Link Pages: 127

DivX Connected DSM-330

Brand: D-Link Pages: 38

Brand: Vdwall Pages: 12

Brand: Vdwall Pages: 5

Brand: Kramer Pages: 14

Brand: OT Systems Pages: 16

Brand: Nitek Pages: 2

Brand: Goobay Pages: 24

PC to TV Converter

Brand: Sewell Pages: 15

Brand: Aegis Pages: 20

PowerVerter Plus PV 1000FC

Brand: Tripp Lite Pages: 20

Brand: Radyne ComStream Pages: 156

MCT-2612 SERIES

Brand: CTS Pages: 2

Brand: 3onedata Pages: 2

Brand: Esu Pages: 8

Brand: Urrea Pages: 12

Brand: J-Tech Digital Pages: 8

Brand: Quickfilter Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands