manualshive.com logo in svg

GRAPHTEC GL820, Service Manual

The GRAHTEC GL820 is a cutting-edge data logger with advanced capabilities. For a hassle-free setup, make sure to check out the Quick Start Manual available for free download on our website. This comprehensive manual will provide step-by-step instructions and help you maximize the potential of your GL820.

Share
Download
background image

GL820-UM-251-9370 

5-1

5. INSPECTION AND CHECK PROCEDURES

5.  INSPECTION AND CHECK PROCEDURES

5.1  Preparations for inspections

5.1.1  AC Line Setting

(1)  Set the AC Line cycle setting of the GL820 to the same cycle as that of your AC line (See Section 4.2).

5.1.2  Sampling setting

(1)  Set the Sampling setting of the GL820 to at least 1 sec or longer.

5.1.3  Copy the condition settings file

Condition settings files  :GL820ConditionVolt.CND 

←

 Condition settings for Voltage accuracy

 

:GL820ConditionTC.CND 

←

 Condition settings for T and K range accuracy

 

:GL820ConditionPT.CND 

←

 Condition settings for PT range accuracy

(1)  Copy the condition settings file to a USB memory device from the computer.

Summary of Contents for GL820





























































Reviews:

No comments

Related manuals for GL820

Solinst Barologger Gold User Manual preview
Barologger Gold
Brand: Solinst Pages: 74
hager HTG410H Installation Manual preview
HTG410H
Brand: hager Pages: 84
Endress+Hauser Ecograph T Technical Information preview
Ecograph T
Brand: Endress+Hauser Pages: 14
Vaisala VaiNet RFL100 Quick Manual preview
VaiNet RFL100
Brand: Vaisala Pages: 172
X2E XORAYA ML-N4000 User Manual preview
XORAYA ML-N4000
Brand: X2E Pages: 190
ICP DAS USA CAN-Logger Series User Manual preview
CAN-Logger Series
Brand: ICP DAS USA Pages: 45
KIC Smart Dock Hardware Manual preview
Smart Dock
Brand: KIC Pages: 27
Ebro EBI 100 Series Manual preview
EBI 100 Series
Brand: Ebro Pages: 40
Eurochron 1486096 Operating Instructions Manual preview
1486096
Brand: Eurochron Pages: 108
AEM AQ-1 Instruction Manual preview
AQ-1
Brand: AEM Pages: 22
Racelogic VBOX Micro User Manual preview
VBOX Micro
Brand: Racelogic Pages: 36
Signatrol spYdaq Hardware Manual preview
spYdaq
Brand: Signatrol Pages: 36
Telemac PFC-12 Instruction Manual preview
PFC-12
Brand: Telemac Pages: 7
Tempilot Tempilot-H8 User Manual preview
Tempilot-H8
Brand: Tempilot Pages: 3
Thunderpaws SportTimer 3000 User Manual preview
SportTimer 3000
Brand: Thunderpaws Pages: 28
Richard Paul Russell SpaceLogger.S10 User Manual preview
SpaceLogger.S10
Brand: Richard Paul Russell Pages: 34
Lumel SM61IoT User Manual & Quick Start preview
SM61IoT
Brand: Lumel Pages: 32
ETI ThermaData Series Quick Start Manual preview
ThermaData Series
Brand: ETI Pages: 2

Brands by name

Popular brands

Load more brands