manualshive.com logo in svg

GRAPHTEC GL820, Service Manual

The GRAHTEC GL820 is a cutting-edge data logger with advanced capabilities. For a hassle-free setup, make sure to check out the Quick Start Manual available for free download on our website. This comprehensive manual will provide step-by-step instructions and help you maximize the potential of your GL820.

Share
Download
background image

GL820-UM-251-9370 

4-1

4. SETUP PROCEDURES

4.  SETUP PROCEDURES

4.1  Entering the System Setup Menu

(1)  Press the [MENU] key until the “OTHR” menu shown below appears.

(2)  Press the [LEFT DOUBLE ARROW Direction] key 10 times in order to display the “Setup” menu shown 

below.

(3)  Move the cursor to the “Mode” position using the [Direction] keys.
(4)  Press the [ENTER] key to display the menu from which you can execute the various Setup operations.

Setup mode

Setup1 (Basic)

Setup2 (Room temp.)

Setup3 (RTD temp.)

(5)  Select the Setup mode using the [Direction] keys, and then press the [ENTER] key.

Summary of Contents for GL820





























































Reviews:

No comments

Related manuals for GL820

Onset InTemp CX450 Manual preview
InTemp CX450
Brand: Onset Pages: 6
iGage Howay T18 Faq preview
Howay T18
Brand: iGage Pages: 16
Adamczewski AD-MM 500 FE Manual preview
AD-MM 500 FE
Brand: Adamczewski Pages: 36
Dostmann 5005-0200 Operating Instruction preview
5005-0200
Brand: Dostmann Pages: 25
Data Harvest EASYSENSE Q3+ User Manual preview
EASYSENSE Q3+
Brand: Data Harvest Pages: 40
Grant Datalogging Squirrel 2020 Series Quick Start Manual preview
Squirrel 2020 Series
Brand: Grant Datalogging Pages: 17
Soil Instruments 1030 User Manual preview
1030
Brand: Soil Instruments Pages: 20
resideo Honeywell Home RNN5 Operating And Installation Instructions preview
Honeywell Home RNN5
Brand: resideo Pages: 33
Acksen EC-3A-RS User Instructions preview
EC-3A-RS
Brand: Acksen Pages: 2
Aranet PRO User Manual preview
PRO
Brand: Aranet Pages: 82
Madge Networks RFPRHTemp2000A Product User Manual preview
RFPRHTemp2000A
Brand: Madge Networks Pages: 16
Lambrecht power[cube] 30.95800.015000 Manual preview
power[cube] 30.95800.015000
Brand: Lambrecht Pages: 10
EasyLog EL-DataPad Quick Start Manual preview
EL-DataPad
Brand: EasyLog Pages: 6
GRAPHTEC GLT400 User Manual preview
GLT400
Brand: GRAPHTEC Pages: 158
Microtronics myDatasensMINI H2S 1000 User Manual preview
myDatasensMINI H2S 1000
Brand: Microtronics Pages: 107
MadgeTech RTDTemp2000 Product Information Card preview
RTDTemp2000
Brand: MadgeTech Pages: 2
InTemp CX405 RTD Manual preview
CX405 RTD
Brand: InTemp Pages: 6
Seneca Z-LTE-WW Installation Manual preview
Z-LTE-WW
Brand: Seneca Pages: 4

Brands by name

Popular brands

Load more brands