Grant Vortex Mag One Installation And Servicing Instructions Download Page 2

GRant EnGinEERinG (UK) LiMitED

Hopton House, Hopton Industrial Estate, Devizes, Wiltshire, SN10 2EU
Tel: +44 (0)1380 736920   Fax: +44 (0)1380 736991
Email: [email protected]   www.grantuk.com

This manual is accurate at the date of printing but will be superseded and should be disregarded if specifications and/or appearances are changed in the interests of continued product improvement. 
However, no responsibility of any kind for any injury, death, loss, damage or delay however caused resulting from the use of this manual can be accepted by Grant Engineering (UK) Limited, the 
author or others involved in its publication.
All good sold are subject to our official Conditions of Sale, a copy of which may be obtained on application.
© Grant Engineering (UK) Limited. No part of this manual may be reproduced by any means without prior written consent.

iMpORtant nOtE FOR instaLLERs

These instructions are intended to guide Installers on the 

installation, commissioning and servicing of the Grant Vortex Mag 

One magnetic filter. After installing the magnetic filter, leave these 

instructions with the user.

spECiaL tExt FORMats

The following special text formats are used in these instructions 

for the purposes listed below:

! WaRninG !

Warning of possible human injury as a consequence of not 

following the instructions in the warning.

! CaUtiOn !

Caution concerning likely damage to equipment or tools 

as a consequence of not following the instructions in the 

caution.

! nOtE !

Used for emphasis or information not directly concerned 

with the surrounding text but of importance to the reader.

pRODUCt CODEs COVERED

These instructions cover the following product codes:
VM01/X

sERViCinG

The magnetic filter should be serviced at least every twelve 

months and the details entered in the Service Log in these 

instructions.

page 2

Summary of Contents for Vortex Mag One













Reviews: