background image

7

Wood Ceiling

1. Saw an oblong groove at a required position (figure 1); Please measure the distance H between concrete roof 

and ceiling surface correctly (figure 2).

Concrete Roof

Roof Surface

Ceiling Surface

Wood Ceiling

H

L(

)

26mm

Total length of screen  minus

15

8m

m

Figure1

Figure2

11. Installation Completed (figure 25).

.Note: the length of M12 bar is 500mm. Please prepare the bar your self if the distance H (between concrete roof 

and ceiling) is longer than 600mm.

Figure25

8

4, Please follow the below steps to install the power cord which recessing in casing . 

1)Take out the power cord (figure 6).

2)Loose the screws of power box and take out the power box (note: the power box must be buttoned on the hanger 

of bracket according to figure 11, please put up and move back the power box to take out), because the power 

cord has a limit, please do not draw it strongly. 

3)Loose and take out two rubber screws, then remove the end cap (figure 8).

4)Remove the line cover of end cap, and then fill in the power line. Afterward, stuck the line cover back to end cap, 

then install the power line outside the casing (figure 9)

5)  Please complete the installation of end cap and fasten two rubber screws; do not need to install the power box 

at this moment.

5. Install the whole screen on the hanging bracket (figure 11-12)

Fi gur e 4

Fi gur e 5

Figure9

Figure7

Figure8

Figure6

Figure11

Figure12

3.Please measure the security distance between hanging brackets (figure 4), and fix the hanging brackets on the 

ceiling using expansion screws (figure 5).

L

26m m

Tot al lengt h of scr een

minus

1

5

8

100

7

9

H

100

minus

Power Line

10

2.This screen equips bracket, and build up the hanging bracket using the hook, M12 nut and M12 bar. Cut the length of M12 bar to 

H minus 100mm(H is the distance between concrete roof and ceiling surface) (Note: H is 500mm, the length of hanging bracket is 

400m which is 500mm minus 100mm) (figure 3).

Fi gur e 3

M12 Bar

M12 nut

Hook 

Brooch

H

1

0

0

m

m

m

in

u

s

100. 0

L

94

minus

1

0

0

H

Power Box

Screw

EXT IR

            

External 

Infrared Receiver

Pow er Li ne

Li ne Cover

Rubber Screw

End Cap

Fo ur Hangi ng 
Boar ds ar e in middl e.

Summary of Contents for RCB-MIR









Reviews: