12
ALARM E8
LEVEL ERROR
DISPLAY DESCRIPTION
E8: Level error
DESCRIPTION
If a water level
10 cm
above the established height is
detected, the cycle is interrupted.
BUZZER
The BUZZER goes on.
ALARM RESET
When the level is back below the safety value the
display prompts “START ?”. The user can either try to
resume the program from same step or go to the end of
the cycle and collect the washing. The alarm can also
be removed by switching the machine off and then on
again.
working condition of the water intake valves
level pressure switch
condition of tub/pressure switch tube
Clean and inspect the water intake valves
Perform level calibration for the electronic card
Replace the tube connecting the tub to the pressure
switch
DO not use very foamy soap.
CHECKS REQUIRED
CORRECTIVE ACTION
ALARM E9
OUT-OF-BALANCE
DISPLAY DESCRIPTION
E9: Out of balance
DESCRIPTION
The tilt switch (the contact connected to MSBIL
opens) notifies that there is a mechanical hazard
involving drum movement and the weight distribution
inside the drum. This alarm is monitored only during
spinning and weighing. The alarm appears on the
display only after the last restart attempt has failed, and
then the cycle is terminated.
BUZZER
The BUZZER goes on.
ALARM RESET
This alarm is reset at the end of the step in which it
occurred, and the door is simultaneously unlocked.
Correct adjustment of the tilt switch.
Correct positioning of the microswitch rod in the
mobile window.
The laundry load needs to be as homogeneous as
possible.
Vibration dampers and shock absorbers must be in
good condition. They must not be discharged or worn
down.
Connect the tilt switch properly.
Position the microswitch rod properly inside the mobile
window.
Optimize the laundry load.
Replace discharged or worn down vibration dampers
and shock absorbers.
CHECKS REQUIRED
CORRECTIVE ACTION
OUT OF BALANCE
OUT OF BALANCE “A”, “B” or “C”
DISPLAY DESCRIPTION
“A”, “B” or “C” flashing on the second screen of the
spinning step (pushing the MODE button).
This
reading is not available for SELFSERVICE versions.
While in the speed = distribution 1, the machine assesses
the distribution quality inside the drum, i.e. how the
laundry items are distributed.
Letter “
C
” stands for good distribution, letter “
B
” stands
for mediocre distribution, and letter “
A
” stands for bad
distribution.
When distribution is assessed to be type “
A
” final spinning
speed will automatically be reduced by 7.5%.
If distribution is type “
B
” or “
C
” maximum spinning
speed remains unchanged.
DESCRIPTION
BUZZER
The BUZZER will not go on.
ALARM RESET
This function is automatically enabled and disabled at each
spinning step.
If distribution type “
C
” occurs often, check that the
laundry load is as equalized as possible.
Vibration dampers and shock absorbers must be in good
condition. They must not be run down or worn out.
CORRECTIVE ACTION
As a rule no corrective action is needed, other than
equalizing the laundry load (using items similar in size and
type).
CHECKS REQUIRED
AUTOMATIC SPEED
REDUCTION
LAUNDRY LOAD TOO BIG OR TOO SMALL
DISPLAY DESCRIPTION
NONE
IF THE AUTOMATIC WEIGHING FUNCTION
HAS BEEN ENABLED
, the machine weighs how heavy
the laundry load contained in the drum is, ex pressing it in
kilos.
If the drum is UNDERLOADED, i.e. the load is 40%
smaller than the rated capacity, or else if the drum is
OVERLOADED, meaning that the load is in excess of
120%, the maximum spinning speed is automatically
reduced by 8% in models for 22kg, it is reduced by 15%
in models for 16.5kg and by 10% in models for 7,4kg and
9,5kg.
BUZZER
The BUZZER will not go on.
ALARM RESET
This function is automatically enabled and disabled at each
spinning step.
CHECKS REQUIRED
Check that the laundry load at issue falls within the
machine's working range.
CORRECTIVE ACTION
As a rule no corrective action is needed, other than
equalizing the laundry load (using items similar in size and
type), and using a load between 40% and 120% of the
machine's capacity rating.
DESCRIPTION
ALARM
MOTOR OVERLOAD SWITCH TRIPPED WITH
AUTORESET ALARMS
1 “
EF Motor fault
”
2 “
OC Motor overcurrent
”
3 “
OV motor overvoltage
”
4 “
UV motor undervoltage
”
5 “
OCH motor failure
”
6 “
ST
motor failure
”
DESCRIPTION
These 6 alarms are read on the display. The listing
priority is from highest to lowest. When in error
condition, the inverter awaits the automatic reset of the
G400 control.
BUZZER
The BUZZER goes on.
Control G400 performs the first reset attempt and the
display prompts “
START?
”.
After 5 consecutive attempts the alarm stays fixed and
can only be removed by switching the machine off and
then on again.
The power voltage supplied to the machine must be in
the range specified in the rating plate.
The wash load MUST NOT exceed the machine’s
rated load.
Connect the appliance to a power source ensuring the
correct voltage.
Optimize the laundry load.
DISPLAY DESCRIPTION
ALARM RESET
CHECKS REQUIRED
CORRECTIVE ACTION
www.groupdynamics-laundry.com
