manualshive.com logo in svg

Grand Banks 1996 Eloise 42 Classic, Operation Manual

Share
Download
Grand Banks 1996 Eloise 42 Classic Operation Manual Download Page 26

 
 

ENTERTAINMENT SYSTEMS 

 

AM/FM Stereo Radio 

 

The stereo unit is located aft of the port door in the cabinet lower shelf.  It operates like a normal car radio.  
There are two speakers (stereo) in the salon, two (stereo) in the master state room and two (stereo) on the 
bridge.  The Clarion is a multi-functional system which includes, CD viewing, IPOD interface, AM/FM 
stereo, etc. To power the system, turn all three STEREO breaker switches on, which are located on the DC 
power panel. See Clarion user manual for operation instructions if needed. 

 
 

TV/DVD  

 
A TV/DVD is located aft of the port door in the cabinet lower shelf. The TV provided to be used for DVD 
movies. Follow the instructions located with the TV to operate the DVD. This device when underway must 
be used with the inverter. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for 1996 Eloise 42 Classic

































Reviews:

No comments

Brands by name

Popular brands

Load more brands