manualshive.com logo in svg

Grand Banks 1996 Eloise 42 Classic, Operation Manual

Share
Download
Grand Banks 1996 Eloise 42 Classic Operation Manual Download Page 18

 
 

 

 

Electric Hot Water Tank 

 

The AC electric HOT WATER HEATER has an 18 gallon capacity tank and is available when connected to 
shore power  or via the generator.  To use  on shore power  or generator,  flip on the water heater circuit 
breaker on the AC electrical panel.  Do not use the water heater if the water tank level is very low.  As with 
any electric hot water tank it takes some time to get the water up to temperature from a cold start. 
 

Everhot Tank 

 

Hot water can also be obtained by utilizing the Everhot system located next to the AC hot water tank on the 
port side of the engine room. This tank colored RED is an integral component used in the Webasto Hydronic 
Heating system. Refer to that section to understand how to utilize its capabilities. 

 

Shower 

 

Before taking a SHOWER, make sure the 

F.W. PUMP

 and shower 

DRAIN PUMP

 breakers are on. In each 

shower stall there is a silver drain knob that activates the drain pump under each floor grate. Make sure you 
pull this ON prior to showering. This pump works automatically when the water level reaches the float lever. 
While taking a shower, if the pump fails to operate, check for hair or debris blocking the float lever. If all is 
clear make sure the shower 

DRAIN PUMP

  breaker is switched on. To help conserve water take  short 

“boat” showers (turning off water between soaping up and rinsing). To keep shower tidy wipe down the 
shower stall and floor.  Check for accumulation of hair in the shower and sink drains.  After use, turn off the 
DRAIN PUMP breaker and ensure that the faucets and nozzle are completely off after use. 

Summary of Contents for 1996 Eloise 42 Classic

































Reviews:

No comments

Brands by name

Popular brands

Load more brands