manualshive.com logo in svg

Graco XHF, Instructions And Parts, Page: 14 / 16

Share
Download
Graco XHF Instructions And Parts Download Page 14

Parts

14

3A2799C

Needle and Seat Kits

The needle and seat are available only in kits that
include items 2a through 2e.

The standard non-diffused needle and seat kit, 237260,
includes all OEM parts and has the number 125
stamped on the needle and seat. It is recommended for
use with mastics, sealers and other high viscosity mate-
rials which have fillers that cannot easily pass through a
diffuser.

The optional needle and seat kit, 237398, has the num-
ber 090 stamped on the needle and seat. This kit will
decrease the maximum flow rate of the gun.

Accessories

207946 Swivel

Connects the gun inlet to the fluid supply hose and
allows easier gun movement and twisting.

Maximum

working pressure is 6500 psi (45 MPa, 450 bar).

24P834 Swivel

Connects the gun inlet to the fluid supply hose and
allows easier gun movement and twisting. This swivel
has a PTFE seal for improved chemical resistance.

Maximum working pressure is 6500 psi (45 MPa, 450
bar).

To reduce the risk of component rupture, and serious
injury, including fluid injection, do not exceed the
gun’s 7250 psi (500 bar, 50 MPa) maximum working
pressure or the maximum working pressure of lowest
rated component in the system.

Summary of Contents for XHF

















Reviews:

No comments