manualshive.com logo in svg

Graco TX 125, Repair Manual

Share
Download
Graco TX 125 Repair Manual Download Page 15

Motor

15

Reassembly

1.

Angle motor pulley through compressor belt (84) 
and pull motor (71) into position. 

2.

Tighten two mounting bolts (105) on motor (71) until 
snug, then back 1/8 of a turn.

3.

Insert torque wrench into square hole (SQ) on motor 
and torque motor to 130-150 in-lb (this may require 
two people; one to torque while the other tightens 
mounting bolts). Tighten motor bolts (105).

4.

Take compressor out of vice and rotate pump pulley 
(104) one full revolution to seat the belt properly.

5.

Place compressor back into vice and torque bolts as 
described in steps 2 and 3. 

6.

Replace fan (72) and tighten set screw.

7.

Replace 

Compressor

; page 9.

8.

Replace 

RotoFlex

™

 II Pump

 hose; page 8.

9.

Replace 

Shroud

, page 7.

When replacing motor (71), make sure the 
square-shaped hole (SQ) is facing toward the out-
side of the compressor. This hole will be used to 
torque the mounting bolts.

SQ

ti8890a

71

84

ti8891a

105

71

ti8896a

104

ti8892a

72

Summary of Contents for TX 125

































Reviews:

No comments

Brands by name

Popular brands

Load more brands