manualshive.com logo in svg

Graco TX 125, Repair Manual

Share
Download
Graco TX 125 Repair Manual Download Page 9

Compressor

9

Compressor

Use Compressor Repair Kit, 288612.

Disassembly

1.

Relieve Pressure, 

page 6.

2.

Unplug sprayer from outlet.

3.

Remove 

Shroud

, page 7.

4.

Remove 

RotoFlex

™

 II Pump

 hose, page 8.

5.

Unscrew and remove grounding screw (49) from 
compressor.

6.

Use 9/16 in. socket and wrench to remove pivot bolt 
(26) and nut (27).

7.

Unscrew and remove second grounding screw (49) 
from bracket (21).

8.

Remove 4 screws (29) and lift bracket (21) off of 
compressor.

9.

Remove shoulder bolt (35) holding pump roller in 
place.

10. Use a wrench to push down on push-to-connect 

fitting and pull out all nylon hoses.

11. Disconnect all electrical wire connectors, see 

Wiring Diagram

, page 25.

12. Thoroughly clean inside housing, removing dust and 

debris.

To service the compressor, remove it from the sprayer 
body and place it a vice. Tighten the vice onto the main 
pulley to hold the compressor in place while servicing.

ti2810b

49

ti8941a

ti9438a

26

27

49

21

ti9013a

ti9440a

29

21

ti8879a

35

ti8952a

ti8951a

Summary of Contents for TX 125

































Reviews:

No comments

Brands by name

Popular brands

Load more brands