background image

Service 

16

308345T

F

IG

. 10: Siphon and Helix Tubes

Remove the Drive Belt

Replace the drive belt (15) if it is cracked or worn.

1.

Remove the siphon tube (4) and helix tube (7) as 
instructed above.

2.

Remove the eight screws (27) and the drive belt 
cover (2). See F

IG

. 11.

3.

Remove the three hex-head screws (14a) and the 
bushing (14).

4.

Slide the drive belt (15) over the smaller pulley (12). 
Then remove the larger pulley (13) and the drive 
belt (15) as shown in F

IG

. 11. Belt must have no 

tension after installation.

F

IG

. 11: Drive Belt

Torque oppositely and evenly to 60 to 70 in-lb (6.8 to 
7.9 N•m).

1

2

Apply PTFE spray lubricant to inside lip of bearing nut before 
you install it.

Apply PTFE spray lubricant to siphon tube (4) inlet end and 
to top 6 in. (150 mm) of helix tube before you install them.

3

Detail A

14a

14

24

41

6

25

4

35

14

7 Ref

3

B

8

7

Detail B

1

3

Model 236629 shown

2

3

To avoid static electricity buildup and possible 
sparking, which could cause fire and explosion, 
replace the drive belt with a genuine ESD rated and 
marked belt only. Order part number 112552. 

With helix tube (7) flush with top of bushing (14), 
torque the screws oppositely and evenly to 55 to 
60 in-lbs (6.2 to 6.8 N•m).

1

2

Model 236629 shown

14a

14

13

15

12

2

27

1

2

Replace with a genuine ESD rated and marked 
belt only.

Summary of Contents for Twistork Helix 308345T























Reviews: