background image

Operation 

10

308345T

kit, to help prevent thick sediment from being forced into 
the siphon inlet.

NOTE: If you install an air shutoff valve, the same 
agitator speed is set each time it is turned on without 
requiring repeated needle valve adjustments.

You can also use an air line quick-disconnect (F) as a 
shutoff. See F

IG

. 6. See Air Line Quick-Disconnect

page 7.

F

IG

. 7: Operate the Agitator

Shutdown Procedure

1.

To stop the agitator, close the needle valve (18), or 
disconnect the quick-disconnect (F), or close the air 
valve in the air supply line.

2.

Follow the Pressure Relief Procedure, page 9.

3.

If you remove the agitator from the drum, remove 
the bearing nut (8), and hang or tilt the agitator 
upright over a container to allow it to drain. Order 
part number 189658, accessory handle, so you can 
connect a lift hook to raise and lower the agitator or 
hang the agitator to store it.

Do not let fluid dry in the fluid tubes. See Clean the 
Fluid Tubes
, page 12.

NOTICE

Do not operate the agitator at a high speed for a long 
period of time. Excessive agitator speed can cause the 
fluid to foam and can cause vibration and increased 
wear on parts and damage to the drum bung. Only 
agitate the fluid fast enough to maintain even mixing. 
You can view fluid movement through the 0.75-in. port 
on the drum cover.

Model 236629 shown

18

F

7

8

4

NOTICE

Keep the agitator upright. Do not lay it on its side or 
upside down, because fluid might flow into the beltdrive 
area causing damage.

If you use the accessory agitator handle, make sure the 
agitator is loosened from the drum before you raise it 
with a lift. The handle will not support the weight of the 
drum.

Summary of Contents for Twistork Helix 308345T























Reviews: