background image

  

PARTS LIST

Model 235–653 Twistork

t

 Helix Mixer

Stainless Steel, with suction feature

Includes items 1 to 23

REF 
NO.

PART NO. DESCRIPTION

QTY

1**

111–310

MOTOR, air; Includes item 1a

1

1a

101–709

S

MUFFLER, exhaust

1

3

101–682

SCREW, cap, sch; 1/4–20 x 0.625 3

4

224–875

HOUSING, outlet, stainless steel

1

5

224–395

SHAFT,  agitator

1

6

224–393

HELIX, agitator

1

7

187–054

PLUG, fluid tube

1

8*

101–946

PIN, cotter

1

9*

111–312

O-RING, Viton

r

1

10

102–207

SCREW, set, socket; 
1/4–20 UNC 3A

2

11

202–233

NEEDLE VALVE ASSEMBLY
Includes items 18a to 18e

1

11a

101–326

S

SCREW, set, sch; #10

1

11b

156–930

S

BARREL, needle

1

11c

159–448

S

HOUSING, valve

1

11d

159–449

S

NEEDLE, valve

1

11e* 159–589

S

O-RING, buna-N

2

12*

187–053

SEAT, check valve

1

13

187–050

HOUSING, check valve

1

14*

105–691

BEARING, ball

1

15

110–208

PLUG, hdless pipe; 1/8–27 nptf

1

16

187–577

PLATE, motor mounting

1

17

102–023

SCREW, cap, hex hd; 
1/4–20 x 0.75

3

20

111–593

SCREW, grounding; hex, No. 8–32 1

22

157–021

WASHER, lock

1

23*

235–994

SEAL KIT; graphite-filled PTFE

1

*

Recommended “tool box” spare part. Keep on hand to
reduce down time.

** An Air Motor Repair Kit is available. Order part no.

224–954.

MANUAL CHANGE SUMMARY

The manual was changed from Rev A to Rev B to make the
following changes:

Assembly
Changed

Status

Ref
No.

Part No.

Name

235–653

DELETED

18

111–923

Seal

DELETED

19

111–922

Seal

ADDED

23

235–994

Seal Kit

DIMENSIONAL DRAWING

8.78 in. 
(223 mm)

33.25 in. 
(845  mm)

2 – 11-1/2 npt

3/4 npt(f)

OUTLET PORT

0910A

To top
of bung

1/8 npt

Summary of Contents for Twistork A Series









Reviews: