background image

INSTRUCTIONS–PARTS LIST

308–246

Rev. B

Supersedes Rev A

This manual contains IMPORTANT

WARNINGS AND INSTRUCTIONS

READ AND RETAIN FOR REFERENCE

AIR DRIVEN

Twistork

 HELIX MIXER

100 psi (7 bar) MAXIMUM WORKING AIR PRESSURE

Model 235–653, Series A

Stainless Steel Agitator, with suction feature
For use in bung-mounted 55 gallon drum

GRACO INC.   P.O. BOX 1441  MINNEAPOLIS, MN  55440–1441

 COPYRIGHT 1992 GRACO INC.

TABLE OF CONTENTS

Warnings

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Installation

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Operation & Maintenance

4

. . . . . . . . . . . . . . . . . . . . . . 

Accessories

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Parts Drawing

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Parts List

7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Dimensional Drawing

7

. . . . . . . . . . . . . . . . . . . . . . . . . . 

Technical Data

Back Cover

. . . . . . . . . . . . . . . . . . . . . . . 

Graco Phone Numbers

Back Cover

. . . . . . . . . . . . . . . 

Warranty

Back Cover

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

0910A

Patented in the United States and Europe

Summary of Contents for Twistork A Series









Reviews: