Graco TI1713A Instructions-Parts List Manual Download Page 26 | Manualshive

Page: 26 / 56

background image

Maintenance

26

309298J

Clean the Spray Gun

Equipment Needed

•

soft bristle brush

•

compatible solvent

Procedure

1.

Relieve the pressure.

2.

Be sure the turbine air (TA) is turned off.

3.

Remove the retaining ring (1), tip guard (3), air cap
(40), spray tip (4), and gun shroud (2). See page 19.

4.

Dip the end of a soft bristle brush into compatible
solvent. clean the front of the gun with the brush.
Avoid getting any solvent into the air passages.
Whenever possible, point the gun down when clean-
ing it. See F

IG

. 15..

If it appears that there is paint inside the air passages,
remove the gun from the line for servicing.

Fig. 15. Clean Front of Gun

5.

Dampen a soft cloth with solvent and wring out the
excess. Wipe the exterior of the gun and shroud
clean. See F

IG

. 16..

Fig. 16. Clean Gun Body

6.

Remove the bottom fluid tube fitting (P) and fluid fil-
ter (20). See F

IG

. 17.. Clean the filter in compatible

solvent.

7.

Reinstall the filter (20) and fitting (P). Do not over-
tighten the fitting, and make sure the top fitting (Q)
remains tight.

WARNING

Skin Injection Hazard

To reduce the risk of a fluid injection injury,
always follow the Pressure Relief Proce-
dure on page 18 when you stop spraying
and whenever you are instructed to relieve
the pressure.

TI1719A

02007

TI1720A

«
...
24
25
26
27
28
...
»

Summary of Contents for TI1713A

























































Reviews:

No comments

Related manuals for TI1713A

Brand: Pro Chem Pages: 2

Brand: AIRLESSCO Pages: 4

Brand: AIRLESSCO Pages: 32

Brand: AIRLESSCO Pages: 36

Brand: Dustbane Pages: 20

IN-LINE GAUGE WITH VALVE

Brand: Task Force Tips Pages: 8

Brand: WAGNER Pages: 30

Brand: WAGNER Pages: 38

Brand: WAGNER Pages: 38

Brand: WAGNER Pages: 40

Brand: WAGNER Pages: 1

Brand: WAGNER Pages: 34

AM-666-NEO 2S Series

Brand: Agrimate Pages: 20

M1 Multi-Sprayer

Brand: Hydro-Force Pages: 8

Brand: Hardi Pages: 36

Brand: Tritech Pages: 60

Brand: Tritech Pages: 60

Ultimate Mx II 1095

Brand: Graco Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands