![background image](http://html.mh-extra.com/html/graco/saniforce-2150/saniforce-2150_operation-manual_2253278016.webp)
Overmolded
Overmolded
Overmolded Diaphragm
Diaphragm
Diaphragm Repair
Repair
Repair
Tools
Tools
Tools Required
Required
Required
• 28 mm open end wrench
Disassemble
Disassemble
Disassemble the
the
the Overmolded
Overmolded
Overmolded Diaphragms
Diaphragms
Diaphragms
NOTE:
NOTE:
NOTE: Diaphragm kits are available in a range of
materials and styles. See Parts section.
1.
Follow the
Pressure Relief Procedure, page 11
Remove power from the motor. Disconnect all
hoses.
2.
Remove the manifolds and disassemble
the ball check valves as explained in
.
3.
Remove the clamps (30) from the fluid covers,
then pull the fluid covers off of the pump.
4.
To remove the diaphragms, the piston must
be moved fully to one side. If the pump is not
attached to the gearbox, turn the shaft by hand
to move the piston. If the pump is still attached
to the gearbox, loosen the screws and remove
the fan cover. Turn the fan by hand to rotate the
shaft to shift the piston to one side.
TIP:
TIP:
TIP: The air cover has 2 holes (H), one at the
9 o’clock position and another at the 3 o’clock
position. Use pin (131), placed in either hole
(H) as a brace for the wrench while removing or
installing diaphragm bolts.
a.
Hold a 28 mm wrench on the wrench flats of
the exposed piston shaft. Grip the diaphragm
securely around the outer edge and rotate
counterclockwise.
b.
Rotate the drive shaft to move the piston fully
to the other side. Repeat step 4a.
5.
To continue with disassembly, see
Disassemble the Center Section, page 18
Reassemble
Reassemble
Reassemble the
the
the Overmolded
Overmolded
Overmolded Diaphragms
Diaphragms
Diaphragms
NOTICE
NOTICE
NOTICE
After reassembly, allow the thread locker to cure
for 12 hours, or per manufacturer’s instructions,
prior to operating the pump. Damage to the pump
will occur if the diaphragm shaft bolt loosens.
TIP:
TIP:
TIP: If you are also repairing or servicing the
center section (drive shaft, piston, etc.), see
Center Section Repair, page 18
, before you put the
diaphragms back on.
1.
Clean all parts and inspect for wear or damage.
Replace parts as needed. Be sure the center
section is clean and dry.
2.
Thoroughly clean or replace the diaphragm bolt
(13). Install the o-ring (34).
3.
Assemble the fluid side plate (9), the diaphragm
(11), the backup diaphragm (12, if present), and
the air side diaphragm plate (10) on the bolt
exactly as shown.
4.
Clean the female threads of the piston shaft
with a wire brush dipped in solvent to remove
any residual thread locker. Apply thread-locking
primer and allow it to dry.
16
3A5133J
Summary of Contents for saniforce 2150
Page 24: ...Parts Parts Parts Parts 2150T 2150T 2150T Pump Pump Pump 24 3A5133J ...
Page 25: ...Parts 2150HS 2150HS 2150HS Ball Ball Ball Check Check Check Pump Pump Pump 3A5133J 25 ...
Page 26: ...Parts 3000HS 3000HS 3000HS Flapper Flapper Flapper Pump Pump Pump 26 3A5133J ...
Page 27: ...Parts 4000HS 4000HS 4000HS Flapper Flapper Flapper Pump Pump Pump 3A5133J 27 ...