Graco RentalPro 230PC Operation, Parts Download Page 43

Page: 43 / 44

Technical Specifications

334603E

Technical Specifications

17C407

Metric

Sprayer
Maximum fluid working pressure

3300 psi

228 bar, 22.8 MPa

Maximum Delivery

0.57 gpm

2.2 lpm

Maximum Tip Size

0.023

Fluid Outlet npsm

1/4 in.

Cycles

700 per gallon

185 per liter

Generator Minimum

3000 W

100–120V, A, Hz

1Ø, 13, 50/60

Dimensions
Height

28 in. (Handle down)

38 in. (Handle up)

71 cm (Handle down)

96.5 cm (Handle up)

Length

23.25 in.

59.1 cm

Width

20.5 in.

52.1 cm

Weight

68.5 lb.

31.1 kg

Noise** (dBa)

@ 70 psi (0.48 MPa, 4.8 bar)

Sound pressure

90 dBa

Sound power

100 dBa

Materials of Constructions
Wetted materials on all models

zinc- and nickel-plated carbon steel, nylon, stainless steel,

PTFE, Acetal, leather, UHMWPE, aluminum, tungsten

carbide, polyethylene, fluoroelastomer, urethane

Notes

* Startup pressures and displacement per cycle may vary based on suction condition,

discharge head, air pressure, and fluid type.
** Sound pressure measured 3 feet (1 meter) from equipment.
Sound power measured per ISO-3744.

Summary of Contents for RentalPro 230PC













































Search results

Summary of Contents for RentalPro 230PC

Reviews:

Brands by name

Popular brands

Graco RentalPro 230PC, Operation, Parts

Search results

Summary of Contents for RentalPro 230PC

Reviews:

Brands by name

Popular brands