manualshive.com logo in svg

Graco RentalPro 230PC, Operation, Parts

Share
Download
Graco RentalPro 230PC Operation, Parts Download Page 28

Troubleshooting 

28

334603E

Electrical

Symptom: Sprayer does not run, stops

running, or will not shut off.

Perform 

Pressure Relief Procedure

, page

9.

1.

Plug sprayer into correct voltage, 

grounded outlet.

2.

Turn the ON/OFF switch 

OFF

 wait 30 

seconds and then turn power back 

ON

 

again (this ensures sprayer is in normal 

run mode).

3.

Turn pressure control knob clockwise 

1/2 turn.

4.

View digital display or remove control 

box cover to view control board status 

light. To determine which code (or any 

other code besides voltage supply) 

refer to the control board status light. 

Turn the ON/OFF switch 

OFF

, remove 

the control cover then turn power back 

ON

. Observe the status light. Blinking 

LED total count equals the error code 

(for example: two blinks equals CODE 

02).

Keep clear of electrical and moving parts 

during troubleshooting procedures. To 

avoid electrical shock hazards when 

covers are removed for troubleshooting, 

wait 7 seconds after disconnecting power 

cord for stored electricity to dissipate.

Problem

What to Check

How to check

Sprayer does not run at all

AND

Display is blank

OR

Control board status light never lights

See flow chart, page 34.

Sprayer does not shut off

AND

Display shows E=02

OR

Control board status light blinks 2 

times repeatedly

Control board.

Replace control board.

Summary of Contents for RentalPro 230PC













































Reviews:

No comments

Brands by name

Popular brands

Load more brands