Graco Reactor 2 E-30i Operation Download

Page: 10 / 94

Models

Models

Reactor 2 E-30i

All base systems include ﬂuid inlet pressure and temperature sensors and Graco InSite

™

. For part numbers,

see

Accessories, page 12

No Air Compressor/Dryer



With Air Compressor/Dryer

Model

E-30i

E-30i with heat

E-30i

E-30i with heat

Base Machine



272079

272080

272089

272090

Maximum Fluid

Working Pressure

psi (MPa, bar)

2000 (13.8, 138)

Approximate Output

per Cycle (A+B) gal.

(liter)

0.0272 (0.1034)

Max Flow Rate lb/min

(kg/min)

30 (13.5)

Total System Load †

(Watts)

7,400

11,600

13,500

17,700

Voltage (phase)

240 VAC (1)

Available Auxiliary

Current at Volts, 60

Hz*



52 Amps (240)

35 Amps (240)

22 Amps (240)

9 Amps (120)

5 Amps (240)

9 Amps (120)

Fusion AP Package



(Gun Part No.)

AP2079

(246102)

AP2080

(246102)

AP2089

(246102)

AP2090

(246102)

Fusion CS Package



(Gun Part No.)

CS2079

(CS02RD)

CS2080

(CS02RD)

CS2089

(CS02RD)

CS2090

(CS02RD)

Probler P2 Package



(Gun Part No.)

P22079

(GCP2R2)

P22080

(GCP2R2)

P22089

(GCP2R2)

P22090

(GCP2R2)

Heated Hose

50 ft (15 m)

24Y240

Heated Whip Hose

10 ft (3 m)

246055



Total system watts used by system, based on

maximum heated hose length of 310 ft (94.5 m)

for each unit.

Full load amps available for auxiliary equipment

when all bare-system components are operating

at maximum capabilities. Available auxiliary

current is based on 310 ft (94.5 m) of heated hose.

An additional 3.0 amps (240 VAC) of auxiliary

current is available for each 50 ft (15.2 m) section

of heated hose that is not used.

Auxiliary current at 120 VAC is available on CB08,

line 1 (circuit breaker pin 2), line 2 current at 120

VAC is used by the air dryer (circuit breaker pin 4).



Available auxiliary current will be less when the

engine is de-rated for site altitude. Reduce the

Available Auxiliary Current in the chart by 2.5

Amps (240 VAC) per 1000 ft (300 m) elevation

increments. If the available auxiliary current is

less than zero, the system conﬁguration may not

support the full load at that altitude.



Includes Complete Air Compressor/Dryer Kit

24U176.
Refer to

Circuit Breaker Conﬁguration Options,

page 33



See

Approvals, page 12



Packages include gun, heated hose, and whip

hose.

332636C

Summary of Contents for Reactor 2 E-30i































































































Search results

Summary of Contents for Reactor 2 E-30i

Reviews:

Related manuals for Reactor 2 E-30i

Brands by name

Popular brands

Graco Reactor 2 E-30i, Operation

Search results

Summary of Contents for Reactor 2 E-30i

Reviews:

Related manuals for Reactor 2 E-30i

Brands by name

Popular brands