background image

Component Identification

3A2817A

7

A

Airless spray gun

Dispenses fluid.

B

Power switch

Turns sprayer ON and OFF.

C

Pressure control knob

Increases (clockwise) and decreases (counter-clockwise) fluid pres-
sure in pump, hose, and spray gun.

D

Pump fluid outlet fitting

Threaded connection for paint hose.

E

Filter

Filters fluid coming out of pump to reduce tip plugging and improve fin-
ish.

F

Endurance

 Pump

Pumps and pressurizes fluid and delivers it to paint hose. 

G

Suction tube

Draws fluid from paint pail into pump.

H

Prime tube (with diffuser)

Drains fluid in system during priming and pressure relief.

J

Prime/Spray  valve 

In PRIME position (pointing down) directs fluid to prime tube.

In SPRAY position (pointing forward) directs pressurized fluid to 
paint hose.

Automatically relieves system pressure in overpressure situations.

K

Serial Tag (below sprayer frame)

Sprayer model and serial number information

L

Inlet screen

Prevents debris from entering pump.

M

Paint hose 

Transports high-pressure fluid from pump to spray gun.

Q

Tip guard

Reduces risk of fluid injection injury.

R

Reversible spray tip

Atomizes fluid being sprayed, forms spray pattern and controls fluid 
flow according to hole size.

Reversed, it unclogs plugged tips without disassembly.

S

Gun trigger safety lever 

Prevents accidental triggering of spray gun.

T

Gun fluid inlet fitting

Threaded connection for paint hose.

V

Gun fluid filter 

Filters fluid entering spray gun to reduce tip clogs.

W

Hose wrap Rack

Stows paint hose.

X

Pail hanger

For transporting pail by its handle.

Summary of Contents for Pro 230ES















































Reviews: