background image

Repair

3A1450B

13

Reassemble the Coupling 
Adapter and Tie Rods to the 
Motor

NOTE: Use this procedure only if the coupling adapter 
(108) and tie rods (104) have been disassembled from 
the motor, to ensure proper alignment of the motor shaft 
to the piston rod (R).

1.

See F

IG

. 5. Screw the tie rods (104) into the motor 

(101) and torque to 50-55 ft-lb (68-75 N•m).

2.

Fill the cavity in the bottom of the motor shaft with 
grease. Lubricate the threads of the coupling 
adapter (105). Screw the adapter into the motor 
shaft and install the pin (106).

3.

Assemble the coupling nut (110) to the piston rod 
(R).

4.

Orient the lower (102) to the motor (101). Position 
the lower on the tie rods (104). Lubricate the 
threads of the tie rods. Screw the tie rod locknuts 
(105) onto the tie rods. Tighten the locknuts and 
torque to 50-55 ft-lb (68-75 N•m).

5.

Insert the collars (111) into the coupling nut (110). 
Tighten the coupling nut onto the coupling adapter 
(108) and torque to 75-80 ft-lb (102-109 N•m).

F

IG

. 5. Reassembly

Torque to 75-80 ft-lb (102-109 N•m).

Torque to 50-55 ft-lb (68-75 N•m).

Apply lubricant.

Torque to 15-17 ft-lb (20-23 N•m).

1

2

3

4

2

3

1

101

109

102

108

TI16615a

103

111

104

105

110

106

113

112

2

4

3

R

Summary of Contents for President 24H627





















Reviews: