background image

23

307982

Technical Data -- 25:1 Bulldog Pump

Category

Data

Maximum working pressure

17.5 MPa, 175 bar (2500 psi)

Air operating range

.07--0.7 MPa, 0.7--7 bar (10--100 psi)

Pump cycles per 3.8 liters (per 1 gallon)

20

Maximum recommended pump speed

for intermittent operation

60 cycles per minute

Air inlet size

3/4 npsm(f)

Fluid outlet size

1 in. npt(f)

Wetted parts

17--4 PH and 304 Grades of Stainless Steel, Chrome--plated Stainless

Steel, Zinc--plated Carbon Steel, Ultra--high Molecular Weight

Polyethylene, Tungsten Carbide, PTFE and FKM

Stroke length

120 mm (4.75 in.)

Pump Performance Chart

To find outlet pressure (bar/psi) at a specific delivery (liter/
min--GPM) and operating air pressure (bar/psi):

1. Locate desired delivery along bottom of chart.

2. Read vertical line up to intersection with selected fluid

outlet pressure curve. Curve slopes from left to right.
Follow left to scale and read outlet pressure.

To find pump air consumption (m

3

/min--CFM) specific delivery

(liter/min--GPM) and operating air pressure (bar/psi):
1. Locate desired delivery along bottom of chart.
2. Read vertical line up to intersection with selected air

consumption curve. Curve slopes from right to left.
Follow right to scale and read air consumption. Follow
left to scale and read outlet pressure.

Summary of Contents for Power-Flo Bulldog



























Reviews: