Graco NAUTILUS Owner'S Manual Download Page 35 | Manualshive

Page: 35 / 64

background image

35

6.

NEVER

put two

UAS

connectors on

one vehicle

UAS

anchor unless specifically

allowed by the vehicle manufacturer

.

7.

All UAS seating positions have tether

anchors.

Secure the top of the seat using

the tether strap. See Section 18.0 Using the
Tether, page 55.

8.

Safety Check for Secure Installation

Perform this test every time you drive with
your child.
Twist and pull child restraint forward and to
both sides to make sure the

UAS

belt does not

lengthen or loosen and the child restraint does
not easily move. The child restraint should
not move side to side or forward more than 1
inch (2.5 cm).

.If child restraint is loose or

not secure, repeat procedure

OR

find another

location for the child restraint, see
Section 7.0 Choosing an Appropriate Vehicle
Seat Location, p. 18.

«
...
33
34
35
36
37
...
»

Summary of Contents for NAUTILUS

































































Reviews:

No comments

Related manuals for NAUTILUS

Brand: JANE Pages: 68

Brand: Maxi-Cosi Pages: 34

Brand: Infasecure Pages: 16

Brand: Quinny Pages: 35

Evolution BS01-B

Brand: Phil & Teds Pages: 26

Brand: Britax Pages: 29

Brand: Britax Pages: 72

Brand: Britax Pages: 2

Brand: Britax Pages: 28

Essentials Allegiance

Brand: Britax Pages: 52

Brand: Cosatto Pages: 57

Brand: Bellelli Pages: 22

Brand: Bellelli Pages: 38

Brand: Bellelli Pages: 66

Brand: Axkid Pages: 56

Brand: TAKATA Pages: 84

Brand: Yngri Pages: 14

Brand: Maxi-Cosi Pages: 162

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands