background image

Repair Kits 

22

312795K

Repair Kits

NOTE: For displacement pump repair kits, see manual 312793. For air motor repair kits, see manual 312796.

Wall Mounting Kits

Includes bracket and hardware.

Cart Mounting Kit 24E879

Includes cart, bracket, and hardware.

Accessories

Overflow Chamber Kit 24E298

Kit includes overflow cup with cap, seals and necessary 
hardware. Parts not sold separately.

Kit Description

LB050A and 

LB050B

LB100A and LB100B

LB150A and LB150B

3.5 in. 
motor

4.5 in. 
motor

4.5 in. 
motor

6.0 in. 
motor

7.5 in. 
motor

3.5 in. 
motor

6.0 in. 
motor

7.5 in 

motor

Coupling Collars (5)
Package of 10

24A619

24A619

24A619

Connecting Kit
Includes three tie rods (3), 
three tie rod nuts (4), air motor 
adapter, if needed (6), 
coupling nut (7), two coupling 
collars (5), and two shields (8)

24A291

24A294

24A294

24A294

24A294

24A291

24A294

24A294

Kit

Air Motor on Pump

24E880

M04xxx

24E881

M07xxx

24E882

M12xxx or M18xxx

Ref. Description

Qty.

101

LID

1

102

O-RING

1

103

BOTTLE

1

104

FITTING, 2 x 1/4-18 npt

1

105

NUT, retaining

1

106

D-SHAPED SEAL, bellows

1

ti15254a

103

101

106

105

104

102

Top Cap

Summary of Contents for Merkur A Series































Reviews: