background image

Repair 

10

309495L

Valve Stem and Seal 

Replacement

If fluid leaks past v-block seal (3), v-block seal

or valve stem (24) may be worn or damaged.

Use following procedure to replace v-block

seal or valve stem.
1.

Perform 

Pressure Relief Procedure

page 4, and engage trigger lock.

2.

Disconnect gun from hose. 

3.

Unscrew spring retainer (21) and 

remove spring (4).

4.

Unscrew spring housing (28) with a 1/8 

inch hex allen wrench.

5.

Unscrew valve seat (35).

6.

Remove adjustment bracket (20) and 

stem nut (1) from stem.

7.

Remove valve stem (24).

8.

Remove seal retainer (27) and v-block 

seal (3). Replace v-block seal.

9.

Secure gun body (17) in an assembly 

fixture.

10. Lubricate and install v-block seal (3) into 

gun body (17) with lips of seal facing into 

housing.

11. Lubricate and torque seal retainer (27) 

into gun body (17) to 100–125 in-lb 

(11.3–14.1 N•m).

12. Lubricate and install valve stem threads 

(24) into gun body (17). Thread stem 

assembly through v-block seal (3).

13. Thread nut (1) all way onto valve stem 

(24).

14. Install adjustment bracket (20) and 

spring housing (28) onto valve stem (24).

15. 15. Apply high strength anaerobic 

sealant (red) to threads on valve seat 

(35). Torque valve seat into gun body 

(17) to 26–32 ft-lb (35.3–43.4 N•m).

16. Lubricate and install spring (4) and spring 

retainer threads (21) in gun body (17).

17. Insert a 1/8 inch hex allen wrench 

through spring retainer (21) and into 

spring housing (28). Adjust trigger travel 

and valve opening to desired position.

18. Tighten stem nut (1) to set adjustment.
19. Adjust spring adjustment screw (21) to 

desired trigger pull force.

Gun Disassembly and 
Assembly

Disassembly

1.

Perform 

Pressure Relief Procedure

page 4, and engage trigger lock.

2.

See 

Valve Stem and Seal 

Replacement

 and perform Steps 2 – 7.

3.

Remove two retaining rings (8), rod (13) 

and trigger (29).

4.

Unscrew setscrew (42), then unscrew 

fluid tube assembly (19) from gun body 

(17).

5.

Remove gun handle screws (9), gun 

handle (14), trigger lock (15), ball (2) and 

spring (7).

6.

Remove seal retainer (27), seal (3) and 

o-rings (5 and 6).

Assembly

1.

See 

Valve Stem and Seal 

Replacement

 and perform Steps 9 – 11.

2.

Lubricate o-ring (6) and install into gun 

body.

3.

See 

Valve Stem and Seal 

Replacement

 and perform Steps 12 – 

14.

NOTICE

Installing valve stem (24) without

turning it clockwise could damage

v-block seal and result in fluid leakage.

NOTICE

To avoid loosening connections and

damaging gun, grip gun body (17), not

handle (14), when removing fluid tube

assembly (19).

Summary of Contents for Inline HD 17Y907

















Reviews: