background image

308–507

16

THE GRACO WARRANTY

WARRANTY AND DISCLAIMERS

Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and

workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. As

purchaser’s sole remedy for breach of this warranty, Graco will, for a period of twenty four months from date of

sale, repair or replace any part of the equipment proven defective. This warranty applies only when the

equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for, any malfunction, damage or wear caused by

faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence,

accident, tampering, or substitution of non–Graco component parts. Nor shall Graco be liable for malfunction,

damage or wear caused by the incompatibility with Graco equipment of structures, accessories, equipment or

materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of

structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective for examination

by Graco to verify the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge

any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If

inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a

reasonable charge, which charges may include the costs of parts, labor and transportation.

DISCLAIMERS AND LIMITATIONS

THE TERMS OF THIS W ARRANTY CONSTITUTE THE PURCHASER’S SOLE AND EXCLUSIVE

REMEDY AND ARE IN LIEU OF ANY OTHER W ARRANTIES (EXPRESS OR IMPLIED), INCLUDING

WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE,

AND OF ANY NON–CONTRACTUAL LIABILITIES, INCLUDING PRODUCT LIABILITIES, BASED ON

NEGLIGENCE OR STRICT LIABILITY . EVER Y FORM OF LIABILITY FOR DIRECT , SPECIAL OR

CONSEQUENTIAL DAMAGES OR LOSS IS EXPRESSLY EXCLUDED AND DENIED. IN NO CASE SHALL

GRACO’S LIABILITY EXCEED THE AMOUNT OF THE PURCHASE PRICE. ANY ACTION FOR BREACH

OF WARRANTY MUST BE BROUGHT WITHIN THREE (3) YEARS OF THE DATE OF SALE.

EQUIPMENT NOT COVERED BY GRACO WARRANTY

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A P ARTICULAR PURPOSE, WITH RESPECT T O ACCESSORIES, EQUIPMENT,

MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not

manufactured by Graco (such as electric motor, switches, hose, etc.) are subject to the warranty, if any, of their

manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these

warranties.

IMPORTANT PHONE NUMBERS

TO PLACE AN ORDER

,  contact your Graco distributor , or call this number to identify the

distributor closest to you:  

1–800–328–0211 Toll Free

FOR TECHNICAL ASSIST ANCE

, service repair information or assistance regarding the

application of Graco equipment:  

1–800–543–0339 Toll Free

Factory Branches:

 Atlanta, Chicago, Dallas, Detroit, Los Angeles, West Caldwell (N.J.)

Subsidiary and Affiliate Companies:

 Canada; England; Switzerland; France; Germany; Hong Kong; Japan

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

PRINTED IN U.S.A. 308–507  5/90

Summary of Contents for Hydra-Clean 308-507

















Reviews: