Graco Husky 515 D51 Series Instructions Manual Download

Page: 34 / 38

308981

Husky 716 Dimensions

9078A

202

201

139

* Pumps with duckbill check

valves are shipped with the

inlet manifold on top and

the outlet manifold on the

bottom. To make the inlet

manifold on the bottom and

the outlet manifold on the

top, rotate each of the four

duckbill assemblies

vertically 180° as shown

below.

SIDE VIEW

PUMP MOUNTING HOLE PATTERN

FRONT VIEW

1/4 npt(f)

Air Inlet

4.25 in.

(108.0 mm)

4.44 in.

(112.8 mm)

3/4 npt(f), bspt(f) or

bspp(f)

7.37 in.

(187.2 mm)

6.62 in.

(168.1 mm)

1.38 in.

(35.1 mm)

7.80 in.

(198.1 mm)

9.18 in.

(233.2 mm)

10.43 in.

(264.9 mm)

3/4 npt(f) or bspt(f)

Fluid Inlets *

NOTE: Bottom port open on 243305,
243306, 243307 and 246485 only.

2.76 in.

(62.5 mm)

4.29 in.

(109.0 mm)

6.04 in.

(153.4 mm)

6.62 in.

(168.1 mm)

4.29 in.

(109.0 mm)

Four 0.28 in.

(7.1 mm)

Diameter Slots

3/4 npt(f), bspt(f) or bspp(f)

Fluid Outlet *

3/4 npt(f) or

bspt(f)

Fluid Outlets

3/4 npt(f)

or bspt(f)

Fluid Inlets *

Summary of Contents for Husky 515 D51 Series







































Search results

Summary of Contents for Husky 515 D51 Series

Reviews:

Related manuals for Husky 515 D51 Series

Brands by name

Popular brands

Graco Husky 515 D51 Series, Instructions Manual

Search results

Summary of Contents for Husky 515 D51 Series

Reviews:

Related manuals for Husky 515 D51 Series

Brands by name

Popular brands