Graco Husky 515 D51 Series Instructions Manual Download | Manualshive

Page: 1 / 38

background image

9246A

Husky 515

Husky 716

9065A

Instructions

Air-Operated

Diaphragm Pumps

308981ZAT

EN

For fluid transfer applications. For professional use only. Only models marked with (*) are
approved for use in European explosive atmosphere locations.

100 psi (0.7 MPa, 7 bar) Maximum Fluid Working Pressure
100 psi (0.7 MPa, 7 bar) Maximum Air Input Pressure

ACETAL*, POLYPROPYLENE, AND PVDF

Husky

™

515

Model No. D 5 1 _ _ _ Acetal NPT Pumps
Model No. D 5 2 _ _ _ Polypropylene Pumps
Model No. D 5 5 _ _ _ PVDF NPT Pumps
Model No. D 5 A _ _ _ Acetal BSPT Pumps
Model No. D 5 B _ _ _ Polypropylene BSPT Pumps
Model No. D 5 E _ _ _ PVDF BSPT Pumps
Model No. D 9 1 _ _ _ Acetal NPT Pumps
Model No. D 9 A _ _ _ Acetal BSPT Pumps

For Additional Models, see Table of Contents

ALUMINUM* AND STAINLESS STEEL*

Husky™ 716

Model No. D 4 D _ _ _ Stainless Steel BSPT Pumps, Remote
Model No. D 5 3 _ _ _ Aluminum NPT Pumps
Model No. D 5 4 _ _ _ Stainless Steel NPT Pumps
Model No. D 5 C _ _ _ Aluminum BSPT Pumps
Model No. D 5 D _ _ _ Stainless Steel BSPT Pumps
Model No. D 9 4 _ _ _ Stainless Steel NPT Pumps
Model No. D 9 D _ _ _ Stainless Steel BSPT Pumps

For Additional Models, see Table of Contents

*These models are certified:

Important Safety Instructions

Read all warnings and instructions in this manual.
Save these instructions.
Refer to the Pump Matrix on page 22 to determine the
model number of your pump.

II 2 GD

Ex h IIC 66°C...135°C Gb
Ex h IIIC T135°C Db

ATEX T-code rating is dependent on the temperature

of the fluid being pumped. Fluid temperature is limited

by the materials of the pump interior wetted parts.

See Technical Data for the maximum fluid operating

temperature for your specific pump model.

1
2
3
...
»

Summary of Contents for Husky 515 D51 Series







































Reviews:

No comments

Related manuals for Husky 515 D51 Series

Brand: GD Pages: 55

Brand: Davey Pages: 8

Brand: Oleo-Mac Pages: 171

Brand: Oase Pages: 2

Brand: Calpeda Pages: 16

Brand: Navien Pages: 108

Brand: Samoa Pages: 40

Brand: Wilo Pages: 76

Brand: CTC Union Pages: 2

Brand: Waterax Pages: 6

Brand: Bard Pages: 24

SUBMERSIBLE DIRTY WATER PUMP 93819

Brand: Pacific hydrostar Pages: 14

Brand: Wilden Pages: 39

Brand: Samoa Pages: 32

Brand: salmson Pages: 48

RESIDENTIAL GAS FIRED WATER HEATERS

Brand: Giant Pages: 8

Brand: Ingersoll-Rand Pages: 1

Brand: Blue Angel Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands