Graco Husky 2150e, Operation Manual

Page: 42 / 44

Technical Data
Component/Model Component/Model Component/Model U.S. U.S. U.S. Metric Metric
Metric
Compressor 28 lb 13 kg
Variable Frequency Drives (2 hp)
Model Model
Model
Hp/kW Hp/kW
Hp/kW
Input Input
Input Voltage
Voltage
Voltage Range
Range
Range
Nominal Nominal Nominal Output Output Output Voltage Voltage Voltage †
17K696 3.0/2.2 170–264 Vac 208–240 Vac, 3 phase
17K697 3.0/2.2 340–528 Vac 400–480 Vac, 3 phase
25B446 5.0/4.0 170–264 Vac 208–240 Vac, 3 phase
25B447 5.0/4.0 340–528 Vac 400–480 Vac, 3 phase
25B448 7.5/5.5 170–264 Vac 208–240 Vac, 3 phase
25B449 7.5/5.5 340–528 Vac 400–480 Vac, 3 phase
† Output voltage is dependent on input voltage.
Fluid Fluid Fluid Temperature Temperature Temperature Range Range Range
NOTICE NOTICE
NOTICE
Temperature limits are based on mechanical stress only. Certain chemicals will further limit the fluid
temperature range. Stay within the temperature range of the most-restricted wetted component. Operating
at a fluid temperature that is too high or too low for the components of your pump may cause equipment
damage.
Fluid Fluid
Fluid Temperature
Temperature
Temperature Range
Range
Range
Aluminum Aluminum Aluminum Cast Cast Cast Iron, Iron, Iron, or or or
Stainless Stainless Stainless Steel Steel Steel Pumps Pumps Pumps
Polypropylene Polypropylene Polypropylene or or or Conductive Conductive Conductive
Polypropylene Polypropylene Polypropylene Pumps Pumps Pumps PVDF PVDF PVDF Pumps Pumps Pumps
Diaphragm/Ball/Seat Diaphragm/Ball/Seat Diaphragm/Ball/Seat
Material
Material Material Fahrenheit Fahrenheit Fahrenheit Celsius Celsius Celsius Fahrenheit Fahrenheit Fahrenheit Celsius Celsius Celsius Fahrenheit Fahrenheit Fahrenheit Celsius Celsius Celsius
Acetal ( AC ) 10° to 180°F -12° to 82°C 32° to 150°F 0° to 66°C 10° to 180°F -12° to 82°C
EPDM Overmolded
Diaphragm (
EO )
-55° to 250°F -48° to 121°C 32° to 150°F 0° to 66°C 10° to 225°F -12° to 107°C
FKM Fluoroelastomer
(
FK )*
-40° to 275°F -40° to 135°C 32° to 150°F 0° to 66°C 10° to 225°F -12° to 107°C
Geolast® ( GE ) -40° to 150°F -40° to 66°C 32° to 150°F 0° to 66°C 10° to 150°F -12° to 66°C
Polychloroprene check
balls (
CR or CW )
0° to 180°F -18° to 82°C 32° to 150°F 0° to 66°C 10° to 180°F -12° to 82°C
Polypropylene ( PP ) 32° to 150°F 0° to 66°C 32° to 150°F 0° to 66°C 32° to 150°F 0° to 66°C
PTFE check balls or
two-piece PTFE/EPDM
diaphragm (
PT )
40° to 220°F 4° to 104°C 40° to 150°F 4° to 66°C 40° to 220°F 4° to 104°C
PVDF ( PV ) 10° to 225°F -12° to 107°C 32° to 150°F 0° to 66°C 10° to 225°F -12° to 107°C
Santoprene® check
balls (
SP )
-40° to 180°F -40° to 82°C 32° to 150°F 0° to 66°C 10° to 225°F -12° to 107°C
TPE ( TP ) -20° to 150°F -29° to 66°C 32° to 150°F 0° to 66°C 10° to 150°F -12° to 66°C
*
The maximum temperature listed is based on the ATEX standard for T4 temperature classification. If you are operating
in a non-explosive environment, FKM fluoroelastomer’s maximum fluid temperature in aluminum or stainless steel
pumps is 320°F (160°C).
42 3A4068H