background image

Repair 

16

311211L

Reassemble the Coupling Rod 
and Tie Rods to the Motor

1.

Loosen, but do not remove, the screws holding the 
adapter plate (J) to the motor (E), on Viscount I Plus 
pumps. See F

IG

. 6. For Viscount II pumps, torque 

screw (N) to 50-55 ft-lb (68-75 N•m) into motor (E).

2.

Screw the tie rods (C) into the adapter plate (J) and 
torque to 50-55 ft-lb (68-75 N•m). On Viscount I Plus 
pumps, the tie rods will engage threaded holes in 
the base of the motor. Viscount II pumps will engage 
into the adapter plate (J).

3.

Fill the cavity in the bottom of the motor shaft with 
grease. Screw the coupling rod (F) into the motor 
shaft until the pin holes align. Install the pin (A) in 
the first hole from the end of the coupling. On Vis-
count II pumps, torque the coupling nut (M) into the 
motor shaft.

4.

Align the lower (D) with the tie rods (C) and loosely 
install the tie rod locknuts (B).

5.

Insert the collars (G) and screw the coupling nut (K) 
onto the coupling rod (F) and torque to 90-100 ft-lb 
(122-135 N•m).

6.

For Viscount I Plus pumps, torque the holding the 
adapter plate (J) to the motor (E) to 15-17 ft-lb 
(20-23 N•m). For Viscount I Plus and Viscount II 
pumps, torque the tie rod locknuts (B) to 50-55 ft-lb 
(68-75 N•m).

F

IG

. 6

Use this procedure only if the coupling rod (F) and 
tie rods (C) have been disassembled from the 
motor, to ensure proper alignment of the motor 
shaft to the piston rod.

Viscount I Plus 
Pump Shown

TI7674b

Torque to 90-100 ft-lb 
(122-135 N•m).

Torque to 50-55 ft-lb 
(68-75 N•m).

Lubricate threads.

1

2

3

1

J

C

G

K

3

2

E

B

A

H

F

D

F

IG

. 7

Viscount II 460 
Pump Shown

TI10466a

3

1

2

Torque to 90-100 ft-lb 
(122-135 N•m).

Torque to 50-55 ft-lb 
(68-75 N•m).

Lubricate threads.

1

2

3

E

F

G

K

H

D

B

C

J

M

N

2

3

Summary of Contents for HIGH-FLO 311211L































Reviews: