background image

3

307878

Symbols

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
corresponding instructions.

Warnings

WARNING

SKIN INJECTION HAZARD

Spray from the gun, hose leaks, or ruptured components can inject fluid into your body and cause an
extremely serious injury, including the need for amputation.  Splashing fluid in the eyes or on the skin
can also cause a serious injury.

Fluid injected into the skin might look like just a cut, but it is a serious injury.  Get immediate
surgical treatment.

Do not point the dispensing valve at anyone or at any part of the body.

Do not put hand or fingers over the valve.

Do not stop or deflect fluid leaks with your hand, body, glove, or rag.

Do not “blow back” fluid; this is not an air spray system.

Always have the tip guard and the trigger guard on the dispensing valve when dispensing.

Be sure the valve trigger safety operates before dispensing.

Lock the valve trigger safety when you stop dispensing.

Follow the Pressure Relief Procedure on page 12 whenever you are instructed to relieve
pressure; stop spraying; clean, check, or service the equipment; and install or clean the spray tip.

Tighten all the fluid connections before operating the equipment.

Check the hoses, tubes, and couplings daily.  Replace worn, damaged, or loose parts immediately.
Permanently coupled hoses cannot be repaired; replace the entire hose.

TOXIC FLUID HAZARD

Hazardous fluids or toxic fumes can cause a serious injury or death if splashed in the eyes or on the
skin, swallowed, or inhaled.

Know the specific hazards of the fluid you are using.  Read the fluid manufacturer’s warnings.

Store hazardous fluid in an approved container.  Dispose of the hazardous fluid according to all
local, state, and national guidelines.

Wear appropriate protective clothing, gloves, eyewear, and respirator.

Summary of Contents for FIRE-BALL





















Reviews: