background image

307456

2

Table of Contents

Warnings

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Installation

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Operation

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Troubleshooting

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Service

7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Parts

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Dimensional Drawings

10

. . . . . . . . . . . . . . . . . . . . . . . . . 

Mounting Hole Layout

10

. . . . . . . . . . . . . . . . . . . . . . . . . . 

Technical Data

11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Graco Warranty

12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Graco Information

12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Symbols

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.

WARNING

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

D

This equipment is for professional use only.

D

Read all instruction manuals, tags, and labels before operating the equipment.

D

Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor.

D

Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

D

Check equipment daily. Repair or replace worn or damaged parts immediately.

D

Do not exceed the maximum working pressure stated on the equipment or in the Technical Data
section for your equipment. Do not exceed the maximum working pressure of the lowest rated
component in your system.

D

Handle hoses carefully. Do not use hoses to pull equipment.

D

Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 66

_

C (150

_

F) or below –40

_

C (–40

_

F).

D

Wear hearing protection when operating this equipment.

D

Comply with all applicable local, state, and national fire, electrical, and safety regulations.

Summary of Contents for Fast-Flo 215963













Reviews: