manualshive.com logo in svg

Graco EnergyComplete 313221H, Instructions - Parts Manual, Page: 12 / 60

Share
Download
Graco EnergyComplete 313221H Instructions - Parts Manual Download Page 12

Setup 

12

313221H

Setup

Locate EnergyComplete Sprayer on a level surface. Do 
not expose EnergyComplete Sprayer to rain.

Connect EnergyComplete Sprayer to the correct power 
source for your model. See T

ABLE

 2. Models with two or 

three power cords must be connected to separate, dedi-
cated circuits. See F

IG

. 5.

The equipment must be grounded. Grounding reduces 
the risk of static and electric shock by providing an 
escape wire for the electrical current due to static build 
up or in the event of a short circuit.

•

EnergyComplete Sprayer: grounded through power 
cord. 

•

Generator (if used): follow your local code. Start and 
stop generator with power cord(s) disconnected.

•

Spray gun: grounded through the supplied fluid 
hoses, connected to a properly grounded Energy-
Complete Sprayer. Do not operate without at least 
one grounded fluid hose.

•

Object being sprayed: follow your local code.

•

Solvent pails used when flushing: follow your local 
code. Use only metal pails, which are conductive, 
placed on a grounded surface. Do not place pail on 
a nonconductive surface, such as paper, plastic, or 
cardboard, which interrupts grounding continuity.

•

To maintain grounding continuity when flushing or 
relieving pressure, hold a metal part of spray gun 
firmly to the side of a grounded metal pail, then trig-
ger gun.

1.

Locate EnergyComplete Sprayer

2.

Electrical Requirements

Improper wiring may cause electric shock or other 
serious injury if work is not performed properly. Have 
a qualified electrician perform any electrical work. Be 
sure your installation complies with all National, State 
and Local safety and fire codes.

3.

Grounding

Summary of Contents for EnergyComplete 313221H





























































Reviews:

No comments