background image

10

11

9

651-3-00   651699

To Adjust the Seat Height

Do not adjust height while child is in

activity center.

Step 1.

Press in the buttons on each

leg to adjust seat to desired

height.

For your

child’s safety, all three legs

must be set to the same

height. Tray must be level.

Step 5.

Ball holder:

Squeeze latches under tray to release

ball holder. 

Pull ball holder out of tray. Open ball holder to

remove ball. Put ball into cup. Turn ball holder

upside down and reinsert into tray as a cup holder.

Push it all the way down onto tray.

Step 6.

Wand:

Pull up on 

handle

of butterfly wand to

detach it from tray for toddler to play with. 

Do not

pull butterfly off handle.

Step 7.

Seat: 

Store in a safe place, not exposed to sun or

heat, in case you wish to convert back to an infant

setup in the future.

Your Entertainer

®

should now look like the open-tray

toddler mode below.

B. Convert toys for toddler use

Step 1.

House:

Replace on tray with 

mirror facing outside of unit. Turn

base counterclockwise to fasten

it to tray.

Step 2.

Shape toys:

Untie string under

tray and remove them. (Shapes

fit into different openings in

house.) Replace string, attached

only to phone, and retie again

under tray. 

Step 3.

Ring loop:

Remove by pulling ends slightly apart under

tray and pushing loop up. Remove rings. Turn loop upside

down. From underside of tray, insert ends of loop back into

holes and push up until peg ends snap in place. Put rings

onto pegs.

Step 4.

Cup:

Reach underneath tray, wrap fingers around cup, and

squeeze toward you with both hands to release pivot pin of

cup from hole in tray. Turn cup around so handle is away

from house as shown, and reattach to tray. Cup now can

pivot to drop ball onto ball track beneath.

Step 2.

Turn house/mirror toy so that rib

on base of house (see closeup)

lines up with arrow on tray. Lift
house to remove.

Step 3.

Unscrew the three large plastic

bolts attaching tray to legs. Do

not try to pull bolts out of tray.

Remove tray from legs.

Step 4.

Underneath tray, pull back finger latch where the two halves

of tray meet. While holding latch, lift right side of tray up to

release it from left half. Pull tray open.

Step 5.

For each leg: (1) push and hold in the leg button; (2) push

leg down to the 

lowest

position. (Top of inner leg section

must

be slightly below top edge of outer leg.)

Tipping or fall hazard. Do not use in 

toddler mode unless legs are set to lowest position.

Step 6.

Place open tray over base so

Graco

®

name is seen through

opening in trays as shown. Align

bolts over holes in legs. 
Starting with bolt under the house,

partially tighten all bolts (to allow

alignment), then fully tighten.

Be sure bolts are tight. Pull up tray at each bolt to make

sure it is attached to leg.

Tray at proper height

Step 2.

After adjusting height of the seat, 

CHECK 

that your

child’s feet can rest completely on the floor of your

activity center. Tray should not be too high or too low.

Remove child and readjust height if necessary.

TRAY TOO HIGH

TRAY TOO LOW

To Convert Your Convertible

Entertainer

®

for Toddler Use

When your child is able to walk, you can convert your

Entertainer

®

into the toddler mode. This open tray

arrangement, along with changing the toys to allow new

activities, can give your child a whole new play experience.

A. Change base and tray

Step 1.

From top of seat, reach

through the leg openings as

shown and pull plastic tabs

(also found at back and front

of seat) slightly inward while

lifting seat to remove.

Lift

Legs 

must

be

at this height!

1. Push in

2. Push

down

Partially tighten

this

bolt first

Mirror faces

outside of unit

Pull pin out

12

Summary of Contents for Convertible Entertainer 4650








Reviews: