background image

306287

3

Symbols

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.

WARNING

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

This equipment is for professional use only.

Read all instruction manuals, tags, and labels before operating the equipment.

Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco
distributor.

Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

Check equipment daily. Repair or replace worn or damaged parts immediately.

Do not exceed the maximum working pressure stated on the equipment or in the 

Technical Data

for your equipment. Do not exceed the maximum working pressure of the lowest rated component
in your system.

Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer.

Wear hearing protection when operating this equipment.

Comply with all applicable local, state, and national fire, electrical, and safety regulations.

MOVING PARTS HAZARD

Moving parts, such as the air motor piston and elevator, can pinch or amputate your fingers.

Keep clear of all moving parts when starting or operating the pump.

Keep hands and fingers away from the elevator, pump support, drum cover, and the lip of the drum
during operation and whenever the pump or elevator is charged with air.

Before servicing the equipment, relieve the air pressure to the elevator and follow the

 Pressure

Relief Procedure in your separate pump manual to prevent the equipment from starting unexpect-
edly. 

Summary of Contents for 306287

















Reviews: