background image

Graco 5-Year Meter and Valve Warranty

3A6673B

43

Graco 5-Year Meter and Valve Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be 
free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of 
any special, extended, or limited warranty published by Graco, Graco will, for a period from the date of sale as defined in 
the table below, repair or replace equipment covered by this warranty and determined by Graco to be defective. This 
warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written 
recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or 
wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, 
accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or 
wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not 
supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, 
accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco 
distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge 
any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the 
equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which 
charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, 
INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A 
PARTICULAR PURPOSE

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees 
that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury 
to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty 
must be brought within one (1) year past the warranty period, or two (2) years for all other parts.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND 
FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR 
COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO

. These items sold, but not manufactured by Graco 

(such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide 
purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying 
equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to 
a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal 
proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in 
English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous 
documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou 
indirectement, avec les procédures concernées.

Graco Information 

For the latest information about Graco products, visit 

www.graco.com

.

For patent information, see 

www.graco.com/patents

TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6928 or Toll Free: 1-800-533-9655,   Fax: 612-378-3590

Graco 5-Year Meter and Valve Extended Warranty

Components

Warranty Period

Structural Components

5 years

Electronics

3 years

Wear Parts - including but not limited to o-rings, seals and valves

1 year

Summary of Contents for 26C354













































Reviews: