manualshive.com logo in svg

Graco 26C265, Instructions Manual, Page: 25 / 40

Share
Download
Graco 26C265 Instructions Manual Download Page 25

Parts

311053L

25

Parts List - 26C625

Replacement safety labels, tags, and cards are 
available at no cost. 

* Parts included in Air Seal Repair Kit 826265 

(purchase separately).

† Parts included in Fluid Seal Repair Kit 826266 

(purchase separately). 

Keep these spare parts on hand to reduce down 
time.

Not assembled. Install when the gun is mounted to 
the manifold blocks. 

‡  Included in OneSeal

™

 Repair Kit XHD010 (5 each 

per package). Purchase separately. 

Ref.

Part Description

Qty.

1

- - - - -

BODY

1

2

- - - - -

HOUSING, fluid

1

3

†

826267

GASKET, fluid, (pack of 10)

2

4

192687

PLUG, fluid, internal, SST

1

5†

114244

PACKING, o-ring, 
fluoroelastomer

1

6†

114340

RING, back-up, PTFE

1

7

XHD001 GUARD, RAC tip

1

9

XHDxxx

TIP, RAC switch (see 

XHD RAC 

Switch Tip Selection Charts

, 

page 31)

1

9a

‡

- - - - -

SEAL, fluid

1

9b

‡

- - - - -

GASKET

1

9c

- - - - -

TIP, spray, XHD RAC

1

10

245858

DIFFUSER, seat, 3/16 in. ball

1

11†

189970

GASKET, diffuser/valve

1

12

826268

NEEDLE, cartridge, assy.

1

13*

114134

GASKET, polyethylene, bottom

1

14

15H317

SCREW, mounting manifold (M5)

6

15

15H318

SCREW, SHCS

2

16

114137

SCREW, set, 6-32, 1/8 in. long

1

17

18C137

STOP, needle, SST

1

18

192453

CAP, piston

1

19

18C161

SPRING, compression

1

20

114139

SPRING, compression

1

21

578002

PISTON, assy

1

22*

115066

PACKING, o-ring, 
fluoroelastomer

1

23*

111450

PACKING, o-ring, 
fluoroelastomer

2

34

114141

WRENCH, hex (not shown)

1

40*

15K097

GASKET, piston cap

1

- - - 

222385 MEDICAL alert card (not shown)

1

Ref.

Part Description

Qty.

Summary of Contents for 26C265









































Reviews:

No comments