manualshive.com logo in svg

Graco 26C265, Instructions Manual, Page: 10 / 40

Share
Download
Graco 26C265 Instructions Manual Download Page 10

Setup 

10

311053L

Flush Spray Gun

Before running any paint through the spray gun:

1. Flush the gun with a solvent that is compatible with 

the fluid to be sprayed, using the lowest possible 
fluid pressure and grounded metal container. Follow 
the 

Daily Flushing Procedure

 procedure, page 15.

2. Perform 

Pressure Relief Procedure

; see page 12.

Install Spray Tip

GG0 Tip

1. Perform 

Pressure Relief Procedure

; see page 12.

2. Install the spray tip (H) and the gasket (J) in the tip 

retainer nut (K). Screw the assembly firmly onto the 
gun. Tighten the assembly with a wrench. 

NOTE:

 Gaskets are included with Streaming Tips 

270XXX or Fan Tips 182XXX.

RAC Tip

1. Perform 

Pressure Relief Procedure

; see page 12.

2. Snap gasket (9b) on fluid seal (9a). Use tool (A) to 

insert gasket and seal into housing (insert the 
seal-end in first). Tip the tool to remove it once the 
seal is in place. 

NOTE:

 Make sure gasket (9b) is snapped onto fluid 

seal (9a) and is properly inserted into the housing. 
Insert tip cylinder (9c) into the housing, then install 
the assembled RAC Tip onto the spray gun. 

3. Install the tip cylinder (9c) as shown. Turn 90 

counterclockwise to the spray position (the arrow 
should face forward). Install the assembled RAC 
onto spray gun. 

NOTE:

 RAC Tip gaskets are included in OneSeal

™

 

repair kit XHD010.

F

IG

. 7: Install GG0 Tip

TI8577a

K

H

J

F

IG

. 8: Install RAC Tip

F

IG

. 9: Install Tip Cylinder

9b

9a

A

9c

Summary of Contents for 26C265









































Reviews:

No comments