background image

Setup 

12

3A7031A

Setup

Navigating Setup and Data Entry

UP and DOWN Arrows:

Press both the UP and DOWN Arrows 
simultaneously for 3 seconds to enter 
SETUP.

Use the UP and DOWN Arrows to 
navigate screens in the up or down 
direction.

Use these buttons to adjust parameters and data 
values.

RIGHT Arrow:

Use this button to move the cursor to 
the right or to select menu items. 

Use this button to save any parameter 
changes.

LEFT Arrow:

Use this button to move the cursor to 
the left.

Use this button to navigate to the 
previous screen. This cancels any parameter 
change made.

Change Settings

Press both the UP and DOWN Arrow buttons 
simultaneously for three seconds to enter SETUP and to 
change settings. 

Note: Setting changes are not saved until Accept is 
selected.

While in SETUP, if a button is not pushed for 1 minute 
the Lubrication Controller returns to idle.

Mode 

Choose either Interval or End On, but both must be set 
up before the Lubrication Controller will be configured 
for your application.

Interval

Configures how frequently the GLC X lubricates the 
product.

Select either Timer Interval or Machine Count 
Interval.

Timer Interval

This sets up how frequently lubrication occurs.

Interval: defines the time between lubrication 
events.

The idle time shows interval time minus the 
lubrication time. If the interval time is 30 minutes 
and the lubrication time is 1 minute, then after a 
lubrication event the idle time is 29 minutes. The 
lubrication events will then be spaced by 30 minutes 
(Interval Time).

Machine Count Interval

This configures the device to wait for a specific 
number of machine actions between lubrication 
events. 

The actions must be presented to the device as a 
machine count input. This is a digital signal input, 
similar to a proximity switch that would be used for 
Cycle mode.

Timeout Option: enables/disables an interval 
backup timeout.

Interval: when timeout is enabled, this feature 
defines the backup timeout for machine count.

Timeout Action: select the action taken (either Lube 
or Alarm) when a machine count timeout occurs.

Lube: the lubrication event starts if the target 
machine counts do not occur within the user defined 
time.

Alarm: an alarm occurs if the targeted machine 
counts do not occur within the user defined time.

Summary of Contents for 26A814



























Reviews: