background image

Using Finishing Tools

3A0245A

13

Automatic Taping

1.

Remove creaser wheel trigger pin.

2.

Attach taper tool to inline valve.

3.

Position creaser wheel trigger and insert pin into 
trigger assembly.

4.

Load tape into taper tool.

5.

Use flow control knob (C) to set material flow rate. 
Turn flow control knob clockwise to increase 
material flow.

NOTE: Fine flow rate adjustments can be made 
using “+” and “-” buttons on inline valve controller. 
Flow rate can only be adjusted relative to position of 
flow control knob. The fine flow rate can only go 
down from, and up to the flow control knob setting.

6.

Place one hand on taper control tube and one hand 
on Inline Controller Valve (JJ) while in use.

7.

Place tape at bottom of joint (slide tube forward to 
feed tape). 

8.

Pull trigger and roll tape over seam keeping taper 
head wheels in contact with wall.

9.

When taper reaches approximately 3 in. (7.5 cm) 
from end of seam, stop completely and pull tube 
back to cut tape.

10. Use drywall knife to detail seams and overlap.

NOTE: Clean all tools thoroughly after every use. Use 
a brush and water to remove all joint compound from 
tools. Once tools have been cleaned, lightly oil using 
any light machine oil.

NOTE: When taping ceilings or corner seams, the 
creaser wheel can be actuated to push the tape into 
the seam by using the creaser wheel trigger.

ti15679a

ti15748a

ti15678a

ti15682a

ti8794a

C

+

-

ti15675a

Summary of Contents for 257100

































Reviews: