background image

Installation

Ground

Ground

Ground The

The

The System

System

System

The equipment must be grounded to reduce the
risk of static sparking. Static sparking can cause
fumes to ignite or explode. Grounding provides an
escape wire for the electrical current.

• Always

Always

Always ground the entire fluid system as
described below.

• The pumps are not

not

not conductive. Any system

used to pump flammable fluids must be properly
grounded.

• Follow your local fire codes.

Before operating the pump, ground the system as
explained below.

• Pump:

Pump:

Pump: Always

Always

Always ground the entire fluid system by

making sure the fluid has an electrical path to a
true earth ground.

• Air

Air

Air and

and

and fluid

fluid

fluid hoses:

hoses:

hoses: Use only flexible grounded

hoses with a maximum of 500 ft (150 m) combined
hose length to ensure grounding continuity.

• Air

Air

Air compressor:

compressor:

compressor: Follow manufacturer’s

recommendations.

• Fluid

Fluid

Fluid supply

supply

supply container:

container:

container: Follow local code.

• Solvent

Solvent

Solvent pails

pails

pails used

used

used when

when

when flushing:

flushing:

flushing: Follow local

code. Use only conductive metal pails, placed
on a grounded surface. Do not place the pail
on a nonconductive surface, such as paper or
cardboard, which interrupts grounding continuity.

Check your system electrical continuity after the
initial installation, and then set up a regular schedule
for checking continuity to be sure proper grounding
is maintained.

Air

Air

Air Lines

Lines

Lines

1.

Install an air regulator and gauge (C) to control
the fluid pressure. The fluid stall pressure will be
the same as the setting of the air regulator.

2.

Locate a bleed-type master air valve (B) close to
the pump and use it to relieve trapped air. Be
sure the valve is easily accessible from the pump
and located downstream from the regulator.

Trapped air can cause the pump to cycle
unexpectedly, which could result in serious
injury from splashing.

3.

Locate another master air valve (D) upstream
from all air line accessories and use it to isolate
them during cleaning and repair.

4.

An air line filter (C) removes harmful dirt and
moisture from the compressed air supply.

5.

Install a grounded, flexible air hose (A) between
the accessories and the 1/4 npt(f) or 1/4 bspt
pump air inlet. Use a hose with a minimum 1/4 in.
ID. If a hose longer than 10 ft (3 m) is required,
use a larger diameter hose.

10

334795F

Tel:  866-777-6060 
Fax: 866-777-6383

Springer Pumps, LLC

Website: www.springerpumps.com 

Int'l: +001 267 404 2910

Summary of Contents for 24X423

































Reviews: