Graco 239824 Instructions And Parts List Download Page 1 | Manualshive

Page: 1 / 14

background image

308687L

EN

Instructions - Parts List

IM5

™

Inline

Electronic Meter

For use with petroleum-based and synthetic oil, antifreeze, and windshield washer fluid
only.

Model: 239824

500 psi (3.4 MPa, 34 bar) Maximum Working Pressure
5 gpm (19 lpm) Maximum Flow Rate

Important Safety Instructions

Read all warnings and instructions in this manual.
Save these instructions.

1
2
3
...
»

Summary of Contents for 239824















Reviews:

No comments

Related manuals for 239824

Brand: VeEX Pages: 2

Brand: Daewoo Pages: 17

Brand: Panasonic Pages: 1

Brand: Magnescale Pages: 64

SourceMeter 2430

Brand: Keithley Pages: 141

Brand: bmcm Pages: 5

Brand: Tektronix Pages: 48

Brand: POSEIDON Pages: 21

Privia PX-860BK

Brand: Casio Pages: 67

Brand: HOKUYO AUTOMATIC Pages: 17

Lange ORBISPHERE 3100

Brand: Hach Pages: 47

Brand: DAKOTA ULTRASONICS Pages: 51

Brand: F&F Pages: 8

Brand: Kawai Pages: 72

IMI SENSORS TOM607A01

Brand: PCB Piezotronics Pages: 20

Brand: Tektronix Pages: 29

Brand: Tektronix Pages: 20

Brand: Alluris Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands