background image

Maintenance

309414N

7

Maintenance

Grounding

The sprayer must be grounded. Grounding reduces the 

risk of static and electric shock by providing an escape 

wire for the electrical current due to static build up or in 

the event of a short circuit.

Grounding a metail pail:

 Connect a ground wire to the 

pail by clamping one end to pail and other end to a true 

earth ground such as water pipe.

To maintain grounding continuity when flushing or 

relieving pressure:

 hold metal part of spray gun firmly 

to side of a grounded metal pail. Then trigger gun.

Pressure Relief Procedure

1. Lock gun trigger safety.

2. Turn engine ON/OFF switch to OFF. 

3. Move pump switch to OFF and turn pressure control 

knob fully counterclockwise. 

4. Unlock trigger safety. Hold metal part of gun firmly 

to side of grounded metal pail, and trigger gun to 

relieve pressure. 

5. Lock gun trigger safety. 

6. Open pressure drain valve. Leave valve open until 

ready to spray again. 

If you suspect that the spray tip or hose is completely 

clogged, or that pressure has not been fully relieved 

after following the steps above, 

VERY SLOWLY loosen 

tip guard retaining nut or hose end coupling to relieve 

pressure gradually, then loosen completely. Now clear 

tip or hose.

DAILY:

 Check engine oil level and fill as necessary.

DAILY: 

Check hose for wear and damage. 

DAILY:

 Check gun safety for proper operation. 

DAILY: 

Check pressure drain valve for proper opera-

tion.

DAILY:

 Check and fill the gas tank. 

AFTER THE FIRST 20 HOURS OF OPERATION:

 Drain 

engine oil and refill with clean oil. Reference Honda 

Engines Owner’s Manual for correct oil viscosity.

WEEKLY:

 Remove air filter cover and clean element. 

Replace element, if necessary. If operating in an unusu-

ally dusty environment: check filter daily and replace, if 

necessary. 

Repack connecting rod (22) top needle bearing after 

every pump change. 

Replacement elements can be purchased from your 

local HONDA dealer. 

WEEKLY: 

Check level of TSL in displacement pump 

packing nut. Fill nut, if necessary. Keep TSL in nut to 

help prevent fluid buildup on piston rod and premature 

wear of packings. 

AFTER EACH 100 HOURS OF OPERATION:

 Change 

engine oil. Reference Honda Engines Owner’s Manual 

for correct oil viscosity. 

SPARK PLUG:

 Use only BPR6ES (NGK) or W20EPRU 

(NIPPONDENSO) plug. Gap plug to 0.028 to 0.031 in. 

(0.7 to 0.8 mm). Use spark plug wrench when installing 

and removing plug. 

INJECTION HAZARD 

The system pressure must be manually relieved to pre-

vent the system from starting or spraying accidentally. 

Fluid under high pressure can be injected through the 

skin and cause serious injury. To reduce the risk of an 

injury from injection, splashing fluid, or moving parts, 

follow the 

Pressure Relief Procedure

 whenever you:

are instructedtorelieve thepressure,

stop spraying, 

check or service any of the system equipment, 

or install or clean the spray tip.

NOTICE

For detailed engine maintenance and specifications, 

refer to separate Honda Engines Owner  Manual, 

supplied. 

Summary of Contents for 233627









































Reviews: