background image

2

307884

Warnings

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

D

This equipment is for professional use only.

D

Read all instruction manuals, tags, and labels before operating the equipment.

D

Use the equipment only for its intended purpose.  If you are not sure, call your Graco distributor.

D

Do not alter or modify this equipment.  Use only genuine Graco parts and accessories.

D

Check equipment daily.  Repair or replace worn or damaged parts immediately.

D

Do not exceed the maximum working pressure stated on the equipment or in the Technical Data
section for your equipment.  Do not exceed the maximum working pressure of the lowest rated
component in your system.

D

Use fluids and solvents that are compatible with the equipment wetted parts.  Refer to the Tech-
nical Data
 section of all equipment manuals.  Read the fluid and solvent manufacturer’s warn-
ings.

D

Handle hoses carefully.  Do not pull on hoses to move equipment.

D

All fluid hoses must have spring guards on both ends.  The spring guards help protect the
hose from kinks or bends at or close to the coupling, which can result in hose rupture.

D

Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces.  Do not
expose Graco hoses to temperatures above 82

_

C (180

_

F) or below –40

_

C (–40

_

F).

D

Do not lift pressurized equipment.

D

Comply with all applicable local, state, and national fire, electrical, and safety regulations.

D

Be sure you know the maximum working pressure of the flexible nozzle you are using.  Never
use a flexible nozzle designed for low pressure dispensing valves or hand-powered lubricating
equipment on a high pressure dispensing valve.

D

Do not modify any part of the dispensing valve; doing so could cause a malfunction and result in
serious bodily injury.  Be sure the dispensing valve has a maximum working pressure that meets
or exceeds that of the pump.

D

The maximum fluid working pressure of these pumps, when operated at a maximum of 180 psi
(1.2 MPa, 12 bar) air pressure is 900 psi (6.2 MPa, 62 bar).

WARNING

WARNING

Summary of Contents for 225728













Reviews: