manualshive.com logo in svg

Graco 17H466, Repair Parts

Share
Download
Graco 17H466 Repair Parts Download Page 45

Troubleshooting

3A3394E Repair - Parts

45

Troubleshooting

General

Problem

Cause

Solution

Engine will not crank

Battery is discharged.

Turn key switch to ON. Choke engine and pull recoil 
starter rope.

Key switch is defective.

Replace key switch.

Main wire harness is defective.

Replace wire harness, see 

Wiring Diagram

, page 68.

Engine cranks slow

Excessive hydraulic load. Engine clutch switch 
is on.

Turn engine clutch switch OFF. 

Engine will not start

Engine is out of gas.

Refill gas tank. See engine manual. 

Fuel shut-off lever is OFF.

Move fuel shut-off lever to ON position. 

Engine oil level is low.

Check oil level and add oil if necessary. See engine 
manual. 

Engine is cold.

Use engine choke.

Spark plug cable is disconnected or damaged.

Connect spark plug cable or replace spark plug cable.

Key switch is defective.

Replace key switch.

Main wire harness is disconnected or defective. Reconnect or replace main wire harness

High engine speed at no load

Improperly adjusted high speed setting.

Reset high speed to 3600 - 3700 engine rpm at no load.

Worn engine governor.

Adjust or replace engine governor.

Machine will not drive

Engine clutch switch is OFF.

Turn engine clutch switch ON.

Hydrostatic drive bypass valve is open.

Close wheel motor bypass valve to engage drive. See 
Operation manual

Hydraulic fluid is low.

Shut off striper and add fluid*.

Drive cable is disconnected or broken.

Reconnect or replace cable.

Clutch wire harness is disconnected or broken.

Reconnect or replace harness as 
necessary.

Clutch does not work.

Replace clutch.

Ground drive belt is worn or broken.

Adjust or replace ground drive belt.

Ground Drive Pump is worn or not working.

Replace ground drive pump.

Wheel motor(s) worn or not working.

Replace wheel motor. 

Summary of Contents for 17H466









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands