background image

Warnings

333028E

3

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation 
point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these 
symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard 
symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.

WARNING

WARNING

WARNING

WARNING

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system 

component. See 

Technical Data

 in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all 

equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information 
about your material, request MSDS from distributor or retailer.

• Turn off all equipment and follow the 

Pressure Relief Procedure 

when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine 

manufacturer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modifications may void agency approvals and 

create safety hazards.

• Use equipment only for its intended purpose. Call your distributor for information.
• Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or 

fluids containing such solvents.

• Comply with all applicable safety regulations.

MOVING PARTS HAZARD

Moving parts can pinch, cut or amputate fingers and other body parts.

• Keep clear of moving parts.
• Do not operate equipment with protective guards or covers removed.
• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, 

follow the 

Pressure Relief Procedure

 and disconnect all power sources.

SKIN INJECTION HAZARD

High-pressure spray is able to inject toxins into the body and cause serious bodily injury. In the event 
that injection occurs, 

get immediate surgical treatment.

• Do not aim the gun at, or spray any person or animal.
• Keep hands and other body parts away from the discharge. For example, do not try to stop leaks 

with any part of the body.

• Always use the nozzle tip guard. Do not spray without nozzle tip guard in place.
• Do not leave the unit energized or under pressure while unattended. When the unit is not in use, turn 

off the unit and follow the 

Pressure Relief Procedure

 for turning off the unit.

• Always engage the trigger lock when not spraying. Verify the trigger lock is functioning properly.

Summary of Contents for 16X423





















Reviews: